Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: check board tracking????

  1. Angry check board tracking????

    I have'nt used my machine for more than a year now due to back surgeries and went to use it a couple of days ago but keep getting the check board tracking message. :>(, My machine only has alittle over 8 hrs of use on it and worked fine the last time i used it. I've cleaned out the machine well and checked all the conections and etc. every thing looks good but still i'm still getting this error code.
    Over the last 6 months or so i've uploaded newer versions of the software and am wondering if that could be putting the machine out of whack so to speak.
    If anyone has any advice at all or if you've had this problem yourself PLEASE HELP!!!

  2. #2
    Join Date
    Feb 2007
    Location
    Upstate NY USA
    Posts
    952

    Default

    Did you try putting the tape around so the sensor picks it up, I've seen that tip.
    " The Hurdier I Go, The Behinder I Get"

  3. #3
    Join Date
    Sep 2011
    Location
    Saginaw, Texas
    Posts
    1,080

    Default

    Make sure the board sensor window is clean of dust. I found using a mild cleaner you can clean the lens with no problem. So start there at cleaning the sensor. Easy thing to try first. You can also check the board sensor on the sensor check - press 0 then 7, that will get you to the sensor check use the up and down arrows to get to the board sensor reading. With a board you can raise and lower in under the sensor to see if it is working. of have a board in the machine and raise and lower the head to read the board.

    James RS has a good tip - I had some dark woods that I have to place masking tape over so the board sensor would read the board and complete the carving.

  4. #4
    Join Date
    Nov 2008
    Location
    Vancouver Island
    Posts
    8,193

    Default

    This error is caused by the brass tracking roller and the x drive motor having a disagreement as to the motion of the board. It will happen if the board losses contact with the brass roller or if the board slips on the sand paper belts. If, for example, the head pressure is too little or if the board is too smooth, the board may slip on the sand paper belt when the board comes to compress (lift) one of the rubber rollers . Try it again and watch to see if the board is slipping on the sand paper belts. If it is slipping, either tighten down the head more and/or put masking tape under the board to help grip the belts.

  5. Default

    Hey ereryone, thanks so much for giving me advice, I tried all of your sugestions with no improvement I'm now getting error codes E-49 032 / E-03 0400 without touching the stop button. I just don't understand what could have went wrong while it set not even plugged in!! Should i just send it in to be worked on and be without it for awhile?
    Thanks so much for trying to help me with this problem.

    Chuck

  6. #6
    Join Date
    Nov 2009
    Location
    Richmond, TX
    Posts
    15

    Default

    Hey chuckles, just had this issue today. In my case, it was the back roller sensor getting stuck during measurement. When it was measuring the sensor wasn't detecting the un-compressed state so when the tracking roller lost contact it came up with "check tracking roller"

    Dr. Al's post http://forum.carvewright.com/showthr...866#post160866 should help if this is the issue.

    as for me, i'm making sawdust again........

  7. Default

    I don;t think that's my issue, tonight i went through the settings and the rollers are compressing and releasing easily, The board sensor is reading 156 under pressure, the only thing i can find wrong is the tracking roller sensor will not read anything when i spin it. Could that be the problem? Is it that i need a new tracking sensor?

  8. #8
    Join Date
    Nov 2008
    Location
    Vancouver Island
    Posts
    8,193

    Default

    If you mean that the x position - board tracking sensor data (0 - 7 up up) reads 0 and does not change when you spin the brass roller, then that is your problem. You may have to take out tracking sensor and have a look. I have not done that myself. Maybe someone else hear can advise you as to what to do and look for.

  9. Default

    I pulled the entire sensor and took out the 2 small screws that holds the back cover on and had a look, Looks ok to me, nothing out of the ordinary but it still won't read anything when i spin it.
    I've tried to contact carvewright thru this forum but nobody will contact me back. What good is customer support when you can't get a response, This is'nt a one time thing either I've tried to order things in the last few months that were never even processed after a month.

  10. #10
    Join Date
    Dec 2006
    Location
    Brunswick, GA
    Posts
    8,123

    Default

    Quote Originally Posted by chuckles2153 View Post
    I pulled the entire sensor and took out the 2 small screws that holds the back cover on and had a look, Looks ok to me, nothing out of the ordinary but it still won't read anything when i spin it.
    I've tried to contact carvewright thru this forum but nobody will contact me back. What good is customer support when you can't get a response, This is'nt a one time thing either I've tried to order things in the last few months that were never even processed after a month.
    Hello,

    I assume you did the sensor check (x-axis) when you rolled the brass sensor by hand...if the numbers don't change, that seems to narrow down the problem.

    As far as CW Tech Support...don't use email...call them. They have excellent Tech Support personnel and is top-notch in my book. The Tech Support phone is: 713-473-6572

    Your ordering issue...I find it very difficult to believe that you placed orders and they were not processed. When you call them, ask about that too. I'm sure they will be able to look up your order history records and see if any orders are still outstanding.
    Michael T
    Happy Carving!


    ═══ Links to Patterns & Resources for CompuCarve™ & CarveWright™ ═══

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •