Page 2 of 2 FirstFirst 12
Results 11 to 18 of 18

Thread: X-drive conveyor stationary tube bearing

  1. #11
    Join Date
    Apr 2009
    Location
    Jefferson, NC
    Posts
    146

    Default

    Measured with caliper.mm is a digital reading, inches was manual caliper, and I got the same problem when I looked number up.
    Love to Make the sawdust, But I sure Hate to clean it up.
    U can't find Success unless you have the patience to hang around long enough to find it!!!!
    Website isn't carving related but a good place to buy a auto:
    www.hcautos.com

  2. #12
    Join Date
    Dec 2014
    Location
    Kaukauna, Wisconsin
    Posts
    767

    Default

    The only real differences I see is the OD of the bearings of which the 688rs bearing that is out there is the smaller of the two. Not sure if you know anyone with a lathe, this could be remedied fairly easy with a sleeve, and your running. The other option out there is if someone is parting a machine. The problem there is they normally sell the whole unit as LHR does.

  3. #13
    Join Date
    Apr 2009
    Location
    Jefferson, NC
    Posts
    146

    Default

    Thanks for your help, I will keep looking.
    Love to Make the sawdust, But I sure Hate to clean it up.
    U can't find Success unless you have the patience to hang around long enough to find it!!!!
    Website isn't carving related but a good place to buy a auto:
    www.hcautos.com

  4. #14
    Join Date
    Dec 2014
    Location
    Kaukauna, Wisconsin
    Posts
    767

    Default

    Another issue I'm having is that LHR went outside OEM bearings to create their machines. For what they are getting for these bearings I would buy them and compare. Like I stated before just get sleeves made and life is good again.

  5. #15
    Join Date
    Dec 2014
    Location
    Kaukauna, Wisconsin
    Posts
    767

    Default

    If you look at picture #2 I think there is a sleeve already in place on your bearing. I can see something like a seam in that picture I believe.

  6. #16
    Join Date
    Apr 2009
    Location
    Jefferson, NC
    Posts
    146

    Default

    Yes you are right I didn't notice that and not much familiar with bearings but a regular 688rs should do the trick thanks
    Love to Make the sawdust, But I sure Hate to clean it up.
    U can't find Success unless you have the patience to hang around long enough to find it!!!!
    Website isn't carving related but a good place to buy a auto:
    www.hcautos.com

  7. #17
    Join Date
    Aug 2008
    Location
    north ont Canada
    Posts
    2,365

    Default

    Quote Originally Posted by badger2424 View Post
    Yes you are right I didn't notice that and not much familiar with bearings but a regular 688rs should do the trick thanks
    If you here your bearing is there https://www.vxb.com/SearchResults.asp?Search=bearin+688
    Henry

    Every one has a photographic memory. Some just don't have film.

  8. #18
    Join Date
    Apr 2009
    Location
    Jefferson, NC
    Posts
    146

    Default

    Ordered, thanks guys
    Love to Make the sawdust, But I sure Hate to clean it up.
    U can't find Success unless you have the patience to hang around long enough to find it!!!!
    Website isn't carving related but a good place to buy a auto:
    www.hcautos.com

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •