Page 1 of 2 12 LastLast
Results 1 to 10 of 18

Thread: X-drive conveyor stationary tube bearing

  1. #1
    Join Date
    Apr 2009
    Location
    Jefferson, NC
    Posts
    146

    Default X-drive conveyor stationary tube bearing

    Rubber Belt wasnít tracking straight took it off an found Iíve got both bearings needed to be replaced on the in feed side of the stationary belt conveyor tube. LHR doesnít sell these an was wondering if anyone knew exact size and a place to order from. Thx for your help.
    Love to Make the sawdust, But I sure Hate to clean it up.
    U can't find Success unless you have the patience to hang around long enough to find it!!!!
    Website isn't carving related but a good place to buy a auto:
    www.hcautos.com

  2. #2
    Join Date
    Sep 2007
    Location
    Northern Colorado
    Posts
    7,764

    Default

    Do you have a part number? I could not find anything in the exploded parts view.
    RingNeckBlues
    My patterns on the Depot
    DC-INSERT It Just Sucks!

    Proven to out perform all others!
    Buy CarveWright
    Colorado FaceBook Users Group


    All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.

  3. #3
    Join Date
    Dec 2014
    Location
    Kaukauna, Wisconsin
    Posts
    497

    Default

    Do you have a way to measure the bearing? Would need OD. ID. and width to cross over. Do you see any numbers on the old bearings at all?

  4. #4
    Join Date
    Aug 2008
    Location
    north ont Canada
    Posts
    2,359

    Default

    Quote Originally Posted by badger2424 View Post
    Rubber Belt wasnít tracking straight took it off an found Iíve got both bearings needed to be replaced on the in feed side of the stationary belt conveyor tube. LHR doesnít sell these an was wondering if anyone knew exact size and a place to order from. Thx for your help.
    You have a private message and go from there
    Henry

    Every one has a photographic memory. Some just don't have film.

  5. #5
    Join Date
    Apr 2009
    Location
    Jefferson, NC
    Posts
    146

    Default

    Bearing has no numbers but it's 3/4" tall, 1/4" wide with 5/16 diameter hole
    Love to Make the sawdust, But I sure Hate to clean it up.
    U can't find Success unless you have the patience to hang around long enough to find it!!!!
    Website isn't carving related but a good place to buy a auto:
    www.hcautos.com

  6. #6
    Join Date
    Apr 2009
    Location
    Jefferson, NC
    Posts
    146

    Default

    Or 19.5mmx6.92mm with 8mm diameter hole
    Love to Make the sawdust, But I sure Hate to clean it up.
    U can't find Success unless you have the patience to hang around long enough to find it!!!!
    Website isn't carving related but a good place to buy a auto:
    www.hcautos.com

  7. #7
    Join Date
    Sep 2007
    Location
    Northern Colorado
    Posts
    7,764

    Default

    Do you have a picture of the part and where it is on the machine?
    RingNeckBlues
    My patterns on the Depot
    DC-INSERT It Just Sucks!

    Proven to out perform all others!
    Buy CarveWright
    Colorado FaceBook Users Group


    All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.

  8. #8
    Join Date
    Apr 2009
    Location
    Jefferson, NC
    Posts
    146

    Default

    Finally found a number with jeweler visor 688RS
    Love to Make the sawdust, But I sure Hate to clean it up.
    U can't find Success unless you have the patience to hang around long enough to find it!!!!
    Website isn't carving related but a good place to buy a auto:
    www.hcautos.com

  9. #9
    Join Date
    Apr 2009
    Location
    Jefferson, NC
    Posts
    146

    Default

    Click image for larger version. 

Name:	image.jpg 
Views:	31 
Size:	1.05 MB 
ID:	86883Click image for larger version. 

Name:	image.jpg 
Views:	39 
Size:	979.1 KB 
ID:	86882 this is the stationary tube in which the rubber conveyor belt rotates on
    Love to Make the sawdust, But I sure Hate to clean it up.
    U can't find Success unless you have the patience to hang around long enough to find it!!!!
    Website isn't carving related but a good place to buy a auto:
    www.hcautos.com

  10. #10
    Join Date
    Dec 2014
    Location
    Kaukauna, Wisconsin
    Posts
    497

    Default

    The bearing number you have is a good number, but the sizes you gave are not the same as the bearing that matches that number. A 688rs measures (ID)8mm x (OD)16mm x (width)5mm. Also wondering how you are doing the measurements as the inch and mm numbers are a bit far apart. 688rs or 6882rs are very easy to come by and are fairly cheap being small bearings.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •