Results 1 to 4 of 4

Thread: Very excited new owner of a CarveWright

  1. Smile Very excited new owner of a CarveWright


    0 Not allowed!
    Good morning everyone. I have my machine and I successfully completed my first small project. I am Retired Army and live near Ft Knox KY. I am busy watching the videos and learning how to work the software. I look forward to hearing from anyone out there that may have a comment.

    I am also a very nervous new user. I am looking for some good advice on doing preventive maintenance and repair. What type of lubricant should I use? Any help would be appreciated

    Tracy Hankins
    U.S. Army Retired
    Last edited by tracyhankins; 08-06-2018 at 10:40 AM. Reason: update post

  2. #2
    Join Date
    Apr 2014
    Location
    Texas
    Posts
    1,932

    Default


    0 Not allowed!
    Tracy,

    Welcome aboard. If you don't have a dust collection system, that would be my first suggestion. It will save you headaches down the road.

    This board is amazing if you do have issues. They helped me when I initially had issues with my machine. Since resolving that issue my machine has run practically without any issues. I deep clean it occasionally, like all my woodworking tools, and lubricate. It is a combination of lubes, with white grease, WD40 and moly grease. The more experienced users can help out on what they use. I don't run my machine very hard or that often compared to most of the folks on here. Their experiences is a lot more relevant.

    Oscar

  3. #3
    Join Date
    Jan 2007
    Location
    NE PA USA
    Posts
    9,801

    Default


    0 Not allowed!
    Welcome Aboard Tracy,

    AL here a Retired Navy Chief. Congratulations on your selection of the CarveWright. I have 6 machines having purchased my first one in 2007 new. The rest are used.

    Lubrication is the biggie when it comes to the flex shaft. Best bet is to purchase the stuff from LHR. Lots of posts on this topic, some use engine assembly lube with good results. My recommendation is to go with the LHR stuff.

    So keep track of your cut motor hours. We recommend at 250 to replace the cut motor brushes and use the LHR version as they are metric. You can find some at ACE Hardware and sand them down but the spring could be longer or shorter and the copper tether acts as a dog leash preventing a short brush from letting the spring metal from getting to the spinning parts. You should get about 5 brush changes if you take care of the brushes. The hardness or softness of the brushes can lead to early motor failure so go with LHR Parts.

    The Y Motor takes a beating. LHR has 2 versions of the Y Gearbox. The Original and the new version. The old one had two 685ZZ Metric Bearings. The new one has a unknown size bigger one and one 685ZZ. It would be good to stock up on the bearings and plan to change them at 250 cut hours. Once they fail, they start to grind down the shaft on the gear.

    You can find lots of posts on the Y Gear Box in the Troubleshooting thread.

    I use chain lube on my flex as I have the very old version before they changed the formula. I also use that for my machine, the threaded rods and smooth rods. Many here use DRY LUBE for this and have good luck with it.

    Join the Facebook CW Page. https://www.facebook.com/groups/1041312339227740/

    And like others have said, get a Dust Collection System. I use the ringneck blues metal version. It Sucks in a good way.. http://www.ringneckblues.com/

    Things to order from LHR:

    Cut Motor Brushes
    Flex Lube
    FFC Cable, the flat cable to the Z. They are a consumable as they can only bend so many times.. And a great source of problems when they are intermittent... Best to have one or 3.... to swap.
    Board Sensor. they can get dust inside the window and give future problems. Best to have one. The TEST.. White copy paper on the board and crank down. Truck over board and call up sensor data on the LCD. A 156 is perfect. A 90 is a dirty window.
    Board sensor CABLE... a 4 wire cable that will help you troubleshoot problems as you can plug the cable in on the top of the truck and plug in your spare senor... The wires can get pinched inside the truck if you pull down on the cable changing the board sensor.

    I don't believe LHR sells the bearings. Use a aftermarket supplier. They DO sell the roller rail bearings.

    Good Luck,

    AL
    Last edited by Digitalwoodshop; 08-06-2018 at 01:52 PM.
    Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.

    Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074

    www.PoconoDigitalWoodshop.com

    www.AccountabilityTag.com


  4. #4
    Join Date
    Jul 2012
    Location
    Springtown, TX
    Posts
    668

    Default


    0 Not allowed!
    welcome aboard!!!! You are in the right place. There are no stupid questions here, we have all been there and are eager to help a newcomer.
    Brent

    A,B machines, PE,probe,conforming vectors, centerline, 2d,3d,stl and dfx imprt, rotary , 3.xx, Pattern Sculptor
    OS X Yosemite

    Woodwork is what I do to pay for my tool addiction.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •