Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15

Thread: Trajectory Assertion Error: E24-0505

  1. #11
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,314

    Default

    What is your head pressure?
    What version of the firmware are you using? It should be 3.102.
    Last edited by lynnfrwd; 01-26-2016 at 09:49 AM.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  2. #12
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,314

    Default

    My guess is...99% of us aren't mechanical/electrical engineers.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  3. #13

    Default

    Quote Originally Posted by lynnfrwd View Post
    What is your head pressure?
    What version of the firmware are you using? It should be 3.102.
    Head pressure was right close to 80lbs if I remember correctly (I will check it again when I have a few minutes). The firmware version is 3.102 - I haven't had the machine a year, and it has under 100hrs on it. It was purchased new from LHR/Carvewright.

    Your comfort level disassembling the machine and mine are two different metrics. Perhaps I can do it just fine with the skill set I have, and perhaps I may make a mistake that voids my warranty. I prefer not to take chances at this point.

  4. #14
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,314

    Default

    The sawdust can cake up at the ends of the two compression rollers. It requires you remove the rollers and clean out the sawdust.

    Look at these documents and see if that makes you feel more comfortable.

    Troubleshooting doc: http://support.carvewright.com/stuck...oller-message/

    Video: http://support.carvewright.com/clean...ssion-rollors/
    Last edited by lynnfrwd; 01-26-2016 at 11:12 AM.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  5. #15
    Join Date
    Sep 2007
    Location
    Northern Colorado
    Posts
    7,962

    Default

    Quote Originally Posted by 2A Finishing View Post
    Head pressure was right close to 80lbs if I remember correctly (I will check it again when I have a few minutes). The firmware version is 3.102 - I haven't had the machine a year, and it has under 100hrs on it. It was purchased new from LHR/Carvewright.

    Your comfort level disassembling the machine and mine are two different metrics. Perhaps I can do it just fine with the skill set I have, and perhaps I may make a mistake that voids my warranty. I prefer not to take chances at this point.
    I was very hesitant to work on the machine in the beginning too but with the online documents and the forum help it became very easy. Even with limited mechanical skills it can be done as the machine is a simple process design. It is not rocket science!
    RingNeckBlues
    My patterns on the Depot
    DC-INSERT It Just Sucks!

    Proven to out perform all others!
    Buy CarveWright
    Colorado FaceBook Users Group


    All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •