Where do you go on the key pad to turn off the question "cut the board" during setup.
Each time you run thru the set up questions, I don't want to answer that question.
Perry B.
Where do you go on the key pad to turn off the question "cut the board" during setup.
Each time you run thru the set up questions, I don't want to answer that question.
Perry B.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
from the main menu, 0-5-4
Now, THAT was worth the price of admission!!
Thanks so much
hey , if you don't ask, you never learn!!!
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
just clear up a question earlier, I should have "cut the board to size" not cut thru board.
I went to 0 5 4 and turn back "ON" , cut thru board", then I arrowed down and found the "prompts" and selected
"cut the board to size" and turned it off.
Perry B.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
Going to do this now, that is annoying each time it pops up
Steve
Start U Member
I just found out that "B" and a "C" machine has 2 different prompts after you enter 0 5, "B" and the "C" are equal until you reach "4", the "C" has "prompts",
from there you can go to 1- cut thru prompt , 2-roller(ask), 3-cut to size, then it goes on 5, 6, 7, 8-lock machine.
The "B" machine matches up 4, then it states "cut thru prompt" and no other options from there, then it moves on to 5, 6, 7. (no
I can not turn off "cut board to size" on the "B" machine.
any help would be great. someone else give this a try if you have a "B" and a"B" machine.
Perry.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
You must be mistaken. The firmware is the same on all the machines. It is the same program.
0-5 is User Options Menu
0-5-4 is Prompts
0-5-4-1 is cut thru?
0-5-4-2 is Rollers?
0-5-4-3 is Cut to size?
Is not 0-5-4-3 the cut board to size?
Last edited by bergerud; 07-13-2015 at 06:08 PM.
0 5 4 has "cut thru prompt" , arrow down to 5 -meas. system ,etc.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
My machines are B. Press 0-5-4-3 and see what you get. Maybe something is wrong with the arrow button.