Results 1 to 9 of 9

Thread: Missing Washer

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Sep 2010
    Location
    Red Deer, AB Canada
    Posts
    43

    Default Missing Washer

    I am finally getting around to replacing the Z-truck with the CarveTight system.
    My assembly has the slot on the lower left side of the casting and therefore, I am suppose to place the washer on the lower right roller.
    However, I did not receive the washer with the other parts.
    Is it a washer I can get at local hardware store or do I need the one LHR is suppose to send?


  2. #2
    Join Date
    Feb 2007
    Location
    SouthWest Ohio
    Posts
    2,346

    Default

    Jimmie,

    The casting has a tapered hole for a flat-head machine screw if I remember correctly.
    Pressure and vibration caused this "wedge" to crack the casting at this point - again trying to remember.
    So, any washer would work although a countersunk one that fits the screw would be best.
    In reality, I think that a round-head screw and a regular washer should work if it is thick and strong enough to distribute the forces.
    The ones I've seen them supply were machined flat and thicker than normal.
    Ken,
    V-1, 2, & 3

    When the People fear their Government, there is Tyranny.
    When the Government fears the People, there is Liberty.
    - Thomas Jefferson

    You must be the change you wish to see in the world.
    - Mohandas Gandhi

  3. #3
    Join Date
    Mar 2007
    Location
    Unionville, NY
    Posts
    298

    Default

    Here is a picture of the washer. Hope this helps.
    Click image for larger version. 

Name:	20150106_183304.jpg 
Views:	54 
Size:	3.16 MB 
ID:	73716

  4. #4
    Join Date
    Jan 2007
    Location
    NE PA USA
    Posts
    9,984

    Default

    For the other users that are wondering what this is about...

    The early Trucks had open slots for a Z homing sensor and a hole for the Probe Data Jack that has been relocated to the side of the cover. The early trucks had a weakness in the mold leaving the bottom right rail bearing hole with a thinner casting. Over time a few cracked as the tapered screw head acted as a wedge splitting the casting. A effective first fix was to add this heavy black washer removing the wedge action and ending the splitting problem. Later the truck was re designed and casted with thicker metal in the bottom right and all holes filled in.

    Heads up to LHR QA to add checking if a washer is needed in the Truck referb to CarveTite check list.

    AL
    Attached Thumbnails Attached Thumbnails DSC03586_WEB.jpg   DSC08344_WEB.jpg   DSC08513a_WEB.jpg  
    Last edited by Digitalwoodshop; 01-07-2015 at 11:41 AM.
    Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.

    Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074

    www.PoconoDigitalWoodshop.com

    www.AccountabilityTag.com


  5. #5

    Default

    I just replaced my Carve-Tight Spindle too. Put the new one in last evening... AGAIN... NO WASHER WITH THE KIT. My new Z truck did not have the tapper and the screws were not PHILLIPS HEAD. They were socket type shouldered machine screws...

  6. #6
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,314

    Default

    I'll check on this today.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  7. #7
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,314

    Default

    New style does not have and uses the socket screw.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  8. #8
    Join Date
    May 2009
    Location
    Deep in the woods of Maine
    Posts
    388

    Default

    The carvetight I just installed had a thicker casting. The bearings that came with it had 2 sets of screws. 1 tapered and 1 shouldered, and there was no washer. The washer is not needed when using the shouldered screw in the shouldered hole.
    -Jason

  9. #9
    Join Date
    Feb 2011
    Location
    New Jersey 07748
    Posts
    828

    Default

    Good info to put into memory bank ,,, To bad this bank gets robbed a lot ... Ha
    Mans Quest for knowledge,,, means he'll always find a way !!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •