Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Sears CompuCarve for sale!

  1. #1
    Join Date
    Mar 2007
    Location
    Buffalo, NY
    Posts
    92

    Default Sears CompuCarve for sale!

    History - I bought one of the earlier systems. After 6 months had some issues and sent it back to Carvewright under warranty. During the shipping back to me, it fell off the UPS truck and was damaged. They sent a me a new machine, which is the one being listed for sale. I never had any issues with this one.

    Last year I bought and installed the new carvetight spindle. I only carved one short item with it. It did make the machine run smoother and slightly quieter.

    I have the original box and foam to ship it in.

    Also have the memory card and reader.

    No bits. Saving them for a CX

    S/N - A. G003.269
    Cut Time - 21 Hrs 30 min.
    On Time - 43 Hrs 26 min
    Servo Time - 34 Hrs 7 Min
    Scanning Time - 9 Hrs 32 Min

    Make Offer

    Cheapest shipping may be Fed Ex
    Pick up available in Buffalo, NY - It's safe to come here, the snows finally gone, maybe!

    Thanks for Looking
    Attached Thumbnails Attached Thumbnails photo 5.JPG   photo 4.JPG   photo 3.JPG   photo 2.JPG  

    photo 1.JPG  
    Go ahead, make my Day!

  2. #2
    Join Date
    Aug 2009
    Location
    outer banks N.C.
    Posts
    123

    Default

    Sent you a p.m.

  3. #3
    Join Date
    Mar 2007
    Location
    Buffalo, NY
    Posts
    92

    Default

    I'd like $800.00 plus shipping. It does have the new carve tight spindle and low cut hours! Never ran any long hour projects, only small signs and projects.
    Go ahead, make my Day!

  4. #4
    Join Date
    Aug 2008
    Location
    north ont Canada
    Posts
    2,365

    Default

    Quote Originally Posted by gtj44 View Post
    I'd like $800.00 plus shipping. It does have the new carve tight spindle and low cut hours! Never ran any long hour projects, only small signs and projects.
    you did say if its B or C machine
    Henry

    Every one has a photographic memory. Some just don't have film.

  5. #5
    Join Date
    Aug 2007
    Location
    North Carolina
    Posts
    1,367

    Default

    The very first post shows the serial number starting with an A.
    Custom Stadium Coin Racks for displaying Military Challenge Coins, GeoCoins and the like- http://www.etsy.com/shop/stadiumdisplays
    OR http://shop.ebay.com/stadiumdisplays...&_trksid=p4340

  6. #6
    Join Date
    Jan 2007
    Location
    NE PA USA
    Posts
    9,984

    Default

    Does it have the A907 14 pin FFC Cable System? or the "A" version 18 pin?

    Has the Board Sensor ever been replced with a glued version.

    Has the L2 Power Supply coil had the Extra Glue added?
    Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.

    Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074

    www.PoconoDigitalWoodshop.com

    www.AccountabilityTag.com


  7. #7
    Join Date
    Aug 2008
    Location
    north ont Canada
    Posts
    2,365

    Default

    Quote Originally Posted by unitedcases View Post
    The very first post shows the serial number starting with an A.
    I seen it now thx an A wow way to much
    Henry

    Every one has a photographic memory. Some just don't have film.

  8. #8
    Join Date
    Mar 2007
    Location
    Buffalo, NY
    Posts
    92

    Default

    I never had the glued board sensor or power supply changed, to be honest, never knew about that upgrade.
    I'll check to see what pin configuration the cable has.

    I have in my original post to make an offer.
    Go ahead, make my Day!

  9. #9
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,314

    Default

    A907 is already done since carvetight upgrade was done.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  10. #10
    Join Date
    Mar 2007
    Location
    Buffalo, NY
    Posts
    92

    Default

    Al Who mentioned if the Board Sensor was replaced with a glued version and L2 Power Supply coil had Extra Glue added?
    What does this do? Does it help the performance or maintenance of the machine?
    Is it an up grade that is available?

    Thanks
    Go ahead, make my Day!

Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •