I just completed this set upon request from a customer this was fun
to do.
Thanks BJB
Perry B.
I just completed this set upon request from a customer this was fun
to do.
Thanks BJB
Perry B.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
these are really good. what did you make these out of
Those were made out of 3/8" Corian, that was my last piece , now I am using 1/4" for every thing.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
Can you share how you've been cutting this and also any tricks for painting.
Thanks
When I need a ptn for a set of coasters I get 2 types, 1 is the ptn and the second is a vector file.
I take the ptn and trace the lines I thinks will give me a good picture. That way I can set the depth I want
for the 1/4" coasters. I use a 1/16", 1/32" depth. I then paint the lines to match the colors I need.T
he Phillies baseball coasters was traced for a file picture I imported in to trace.
The Eagle was trace right off the ptn, since the vector file was too busy for a 60 deg. V bit. I had to remove some of the lines
myself.
You really can't use a carved ptn on a coaster, it could leave a unsmooth surface and you don't know what they are going to place
on the coaster.
see the attached
I hope this helps
Perry B.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
Perry,
Do you paint the lines then sand off excess or do you just paint within the lines. Also are you just cutting this with a table saw and do you use any special blade?
I paint the lines most of the time, if I have to paint inside the lines, I sand off the excess of the lines, then paint between
the lines and spray a high gloss sealer for looks.
I cut the 4 coasters with my table saw with a thin blade. It cuts the coaster material very easly.
I use a 8" x 8" piece in my sled and let her rip.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
Looking good as always Perry
Fair winds,
Capt Bruce
Kinney deSigns http://kinneydesigns.us
CarveWright START U Team Member.
30 year USN SEABEE, the original Weapons of Mass Construction.
Designer Ver 1.187 and 2.007, Ver.3.001 One 2009 B CW w ROCK and a 5th Year Anniversary C CW
Rotary Jig, 2D and 3D, Tracing Probe, DFX and STL Importers
.
Very Cool ,,,,
Mans Quest for knowledge,,, means he'll always find a way !!
Perry nice job on the eagle pnt. They will make nice coasters.