Page 3 of 3 FirstFirst 123
Results 21 to 28 of 28

Thread: Things I like about Designer 2.0

  1. #21
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,314

    Default

    I was so excited about being able to rotate the board 90 degrees to see your project in portrait without getting a crick in my neck.

    Now, I'm even more excited that the next release will have the ability to turn the back side of your board 180 degrees, so you can go from front to rear 180 and make sure your two-sided card is lined up properly.

    Just remember to roll it over in the machine, not flipping end to end.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  2. #22
    Join Date
    Sep 2007
    Location
    Northern Colorado
    Posts
    7,962

    Default

    Quote Originally Posted by lynnfrwd View Post
    I was so excited about being able to rotate the board 90 degrees to see your project in portrait without getting a crick in my neck.

    Now, I'm even more excited that the next release will have the ability to turn the back side of your board 180 degrees, so you can go from front to rear 180 and make sure your two-sided card is lined up properly.

    Just remember to roll it over in the machine, not flipping end to end.
    What is the timing of the next release???
    RingNeckBlues
    My patterns on the Depot
    DC-INSERT It Just Sucks!

    Proven to out perform all others!
    Buy CarveWright
    Colorado FaceBook Users Group


    All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.

  3. #23
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,314

    Default

    Not sure....soon.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  4. Default

    Has the issue that has been mentioned in 187 been addressed in 2.?? And in 187 for that matter?

  5. #25
    Join Date
    Oct 2007
    Location
    Conroe, Texas, United States
    Posts
    1,550

    Default

    It just keeps getting better all the time with designer.

    All at LHR/CW are doing wonderful things.

    I love designer...............
    Happy Carving

    Robert D.
    rcdages

    CarveWright START U Team Member.

    The mightiest oak in the forest is just a little nut
    that held it's ground.

  6. #26
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,314

    Default

    Quote Originally Posted by TerryT View Post
    Has the issue that has been mentioned in 187 been addressed in 2.?? And in 187 for that matter?
    I know it has been / is being address. That is all.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  7. #27

    Default

    I can't seem to find any toggle for rotating the board 90 degrees....I'm sure it's right in front of me...help? I like the ability to put the letters onto a curve...now if I can just figure out how to put the letters inside a waving banner....when I drew a banner using the connected lines the only way I could add the letters was on top of the banner not inside the banner. And the banner wouldn't carve unless I chose a carve out region and I finally found a work around by adding a "pattern" to the bottom of the carve out and putting a .001 depth on it. I know it's the operator and not the software...

  8. #28
    Join Date
    Nov 2008
    Location
    Vancouver Island
    Posts
    8,193

    Default

    The board rotate is in the view menu and also there as a pull down beside the F (front) button. Click the small down arrow.

    Post an mpc of what you are trying to do.

Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •