Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 34

Thread: Axis stall - Z Axis stall E06-0313 - Z and Cut motor tests just loop

  1. #21
    Join Date
    Feb 2008
    Location
    NLR. Arkansas
    Posts
    642

    Default

    Correct , changed the FCS cable twice , I can go to sensor check and readings are fine when I move the truck . But the very moment I press buton to start a project I get the error
    Start U Member

  2. #22
    Join Date
    Jan 2007
    Location
    NE PA USA
    Posts
    9,984

    Default

    Swap Controllers.... with caution....since Calibration Data is different... just get it to get past the point of the other machine...

    AL
    Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.

    Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074

    www.PoconoDigitalWoodshop.com

    www.AccountabilityTag.com


  3. #23
    Join Date
    Feb 2008
    Location
    NLR. Arkansas
    Posts
    642

    Default

    it is the controller board,, took the one out of problem machine and put in running machine and get the , E06-0313 error z axis stall as soon as i hit enter on project, New controller is over $300.
    I do have a controller off a spare parts machine, can it be used? Can it be recalibrated for my machine?
    steve
    Start U Member

  4. #24
    Join Date
    Sep 2007
    Location
    Northern Colorado
    Posts
    7,935

    Default

    You should be able to swap that out and yes you will need to go through the calibration procedures. Any machine info (ID etc.) will be for the machine you took it out of.
    RingNeckBlues
    My patterns on the Depot
    DC-INSERT It Just Sucks!

    Proven to out perform all others!
    Buy CarveWright
    Colorado FaceBook Users Group


    All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.

  5. #25
    Join Date
    Feb 2008
    Location
    NLR. Arkansas
    Posts
    642

    Default

    is there a pdf on the calibration procedure?
    "i found the pdf "
    Start U Member

  6. #26
    Join Date
    Sep 2007
    Location
    Northern Colorado
    Posts
    7,935

    Default

    Quote Originally Posted by skeeterman View Post
    is there a pdf on the calibration procedure?
    "i found the pdf "
    Yes it is on the site under procedures.
    RingNeckBlues
    My patterns on the Depot
    DC-INSERT It Just Sucks!

    Proven to out perform all others!
    Buy CarveWright
    Colorado FaceBook Users Group


    All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.

  7. #27
    Join Date
    Jan 2007
    Location
    NE PA USA
    Posts
    9,984

    Default

    If your not going to turn it in for the purchase of another, I would love to buy it off of you to play with...

    AL
    Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.

    Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074

    www.PoconoDigitalWoodshop.com

    www.AccountabilityTag.com


  8. #28
    Join Date
    Feb 2008
    Location
    NLR. Arkansas
    Posts
    642

    Default

    I havent been able to reset calibration yet with different controller as of yet Al,( no time today) if i can get it going i will get with you on the bad controller
    steve
    Start U Member

  9. #29
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,309

    Default

    Controllers have to be programmed by us and includes the machine serial number.

    The controller has a $100 value when sent in to us, and you qualify as the purchaser.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  10. #30
    Join Date
    Feb 2008
    Location
    NLR. Arkansas
    Posts
    642

    Default

    so controller i had on spare part machine will not work on machine i am trying to fix?
    steve
    Start U Member

Page 3 of 4 FirstFirst 1234 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •