Hello,
I've been saving to buy a CarveWright and I came across a used one that has a probe with it. Does the probe require special software in order to work?
Thanks,
Shane
Hello,
I've been saving to buy a CarveWright and I came across a used one that has a probe with it. Does the probe require special software in order to work?
Thanks,
Shane
Shane,
The probe does come with the pattern editor software and most time if it is a used machine the software has already been activated making the probe just a tool. You can purchase the pattern editor software with out the probe. The same is true for all software additions beyond the basic software that comes with the machine..
RingNeckBlues
My patterns on the Depot
DC-INSERT It Just Sucks!
Proven to out perform all others!
Buy CarveWright
Colorado FaceBook Users Group
All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.
Basically the software for the probe is $200. But for $212 at Lowes you can get the software and the probe. You are asking the wrong questions, so I will give you some answers you didn't ask. There are 3 models of the carvewright. A, B, C. There are three different "chuck" options. The original is the QC, it requires a lot of additional maintenance. And if not maintained properly, will fail. The two other chucks are the CarveTight and the Rock. Both are better chucks. You should take these in consideration, because if what you are buying has a QC, you are going to want to change it. To a tune of $150. If you have an A model you need to make sure the ribbon cable to the Trucks is a 14 pin cable or when it wears out you will have to upgrade the boards to match the new 14 pin cable. Another $150. Also did you check the prices at Carvewright.com. Most other places are charging more. And most of Ebays prices are absurd!! Let us know what you are looking at, and price and we can help you from there!
"Carved with Love"
Happiness comes from within.
But joy comes from helping others.
Measure twice... and then sneak up on it!
The one I purchased, but have not received yet is a model CW.01.01. Not sure which that is, but it was completly updated at Carvewright in 2011. So I'm not sure which model that is an a, b, or c
RingNeckBlues
My patterns on the Depot
DC-INSERT It Just Sucks!
Proven to out perform all others!
Buy CarveWright
Colorado FaceBook Users Group
All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.
Thanks for the help on this. I don't have the serial number. I can't wait to get it and start carving though. It went back to carvewright in 2011 for a spindle, rubber belts, alignment, etc and hasn't been used since. I'm still kind of new to this, but will all the bits fit all the machines with the proper bit adapters?
It sounds like they did the upgrade package http://store.carvewright.com/product...cat=297&page=1 so it is most likely a B version machine. The CarveTight chuck is 1/2" chuck and will accept 1/4" bits by using the 1/4" split collet. If any of the bits have the old quick change adapters on them they will have to be removed to be used in the new chuck.
Great time to go to the main CW site and start digesting all that you can in the support section..
RingNeckBlues
My patterns on the Depot
DC-INSERT It Just Sucks!
Proven to out perform all others!
Buy CarveWright
Colorado FaceBook Users Group
All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.