Page 2 of 2 FirstFirst 12
Results 11 to 17 of 17

Thread: Problem with clear plastic door

  1. #11
    Join Date
    Jan 2007
    Location
    NE PA USA
    Posts
    9,984

    Default

    I just love spending other peoples money....

    I would add to that the Cut Motor Brushes as you will need them for the 250 hour maintenance and the $5.00 brushes when too short can snap that $40.00 cutting bit... The X Gear is good to have when you get a jam on a weekend... The Y Gear box gear is nice if you wait to replace the inner Y Gear Box Bearings and the shaft gets worn on the Y Gear. It is recommended to replace the 2 inner Y Gear Box Bearings at 250 Cut Hours when you change the Cut Motor Brushes.

    And Sand Paper Belts if you use them.

    Good Luck,

    AL

    Buy Locally or on line. http://www.avidrc.com/product/1/bear...-bearings.html
    Attached Thumbnails Attached Thumbnails LHR Order 8 2011.jpg  
    Last edited by Digitalwoodshop; 01-17-2013 at 02:54 PM.
    Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.

    Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074

    www.PoconoDigitalWoodshop.com

    www.AccountabilityTag.com


  2. #12
    Join Date
    Feb 2009
    Location
    San Diego, Ca
    Posts
    70

    Default

    Just had the cut motor rebuilt so no worries there. Already have spares for the Y and X gears as well and a cpl bearing rollers.....

  3. #13
    Join Date
    Jan 2008
    Location
    As of 6/2021 Punta Gorda, Florida
    Posts
    1,461

    Default

    Al... you must not have ordered brushes for awhile. Those $5.00 brushes are now $10.00 pr.

  4. #14
    Join Date
    Jan 2007
    Location
    NE PA USA
    Posts
    9,984

    Default

    Quote Originally Posted by SharonB View Post
    Al... you must not have ordered brushes for awhile. Those $5.00 brushes are now $10.00 pr.
    Your correct... 8 of 2011....

    AL
    Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.

    Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074

    www.PoconoDigitalWoodshop.com

    www.AccountabilityTag.com


  5. #15
    Join Date
    Feb 2009
    Location
    San Diego, Ca
    Posts
    70

    Default

    Got everything in today replaace it all and still the same result....z axis stall...error E06-1313...shows this error after selecting the carving i want to do.....any suggestions????

  6. #16
    Join Date
    Jan 2007
    Location
    NE PA USA
    Posts
    9,984

    Default

    IF I remember correct, that error number shows up when you place a board in the machine thicker than 1 inch and you are trying to do a Cut Path? And it happens just after your machine does the left side BOB down to the Brass Roller plate....


    Let us now...


    AL
    Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.

    Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074

    www.PoconoDigitalWoodshop.com

    www.AccountabilityTag.com


  7. #17
    Join Date
    Feb 2009
    Location
    San Diego, Ca
    Posts
    70

    Default

    The error comes up when i press the project and throws the error before it even moves...was testing the y axes by hand and its working but the z when move it up and down its not showing anything....why?

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •