I'm looking for a Dallas cowboys helmet with the star on it pattern
any help would great.
Perry B.
I'm looking for a Dallas cowboys helmet with the star on it pattern
any help would great.
Perry B.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
Go to this link, and click on EDIT > FIND, and type DALLAS. You should find what you wish.
AskBud
http://forum.carvewright.com/misc.ph...chments&t=2046
Last edited by AskBud; 07-18-2012 at 11:19 AM.
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29
Thanks Bud , never thought to look in that file and I have a copy of too.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
Thanks you BJ, now I have 2 PTNs to take a look at.
Perry B.
My Shop 1044
CarveWright START U Team Member
V - 1.187 and 3.0 too
With the DC Insert," dust all gone"
CarveWright Customer Documentation http://www.carvewright.com/2010CWweb/maintenance.htm
CarveWright Tips and Tricks http://www.carvewright.com/2010CWweb/tips.htm
www.customcarvingsbyperry.com
I have often wondered why it is that
Conservatives are called the "right" and Liberals are called the "left".
"The heart of the wise inclines to the right, but the heart of
the fool to the left."
I am looking for a small round box pattern. would like it to be about 2-3 inches round and about 2 inches high.. not sure if thats possible... have tried to figure out gimp but I am unable to create my own.. anybody have any ideas?? I am open and am willing to buy the pattern. Thanks!
You, probably, need no extra software for your round box. Start by reviewing the April '09 Tip & Trick. Also, remember that you have a depth of cut/carve limit on both the cutting (1 inch) and carving (.8 inch) bits.
http://www.carvewright.com/downloads...icks_Apr09.pdf
AskBud
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29
As Bud said, no need for external software. Using designer alone (none of the 3d suite) I made this example file for you to review, and learn from to make the round box you are looking for.
You wil need the latest designer software 1.184 to open this mpc file.
Or take a look at the second box where a design is placed on the top lid. Removing the feather on the rose will eliminate the carve in the waste area. But as I stated it is waste so nothing to worry about.
Last edited by eelamb; 07-22-2012 at 02:04 PM.
Using Designer 1.187, STL importer, Center line, conforming vectors, scanning probe/PE, and the ROCK chuck.
Eddie
thank you so much Bud.... once again you come thru!!
also eelamb I appreciate that and I think it might work out better since it is smaller than the one bud suggested.... what a great bunch of guys on here... always get an answer to my questions so quick! thanks so much!