Page 2 of 5 FirstFirst 1234 ... LastLast
Results 11 to 20 of 49

Thread: Troubleshooting PDF's

  1. #11
    Join Date
    Jul 2007
    Location
    Roselle, Illinois (Chicago Area)
    Posts
    175

    Default A Troubleshooting Guide from LHR

    Here you go.
    Attached Files Attached Files
    Craig

  2. #12
    Join Date
    Jul 2007
    Location
    Roselle, Illinois (Chicago Area)
    Posts
    175

    Default Here is one for lubricating the Truck Housing

    Found this out the hard way. My flexshaft melted with 52 hours on it. Called LHR, said the truck housing has to be lubed after 20 hours.
    Attached Files Attached Files
    Craig

  3. #13
    Join Date
    Nov 2006
    Location
    Rolla, Missouri
    Posts
    3,418

    Default Z pack replacement PDF.

    Here is a link to the Z-pack replacement PDF.

    http://www.carvewright.com/downloads...e%20z-pack.pdf
    Happy carving , Jeff Birt

    Check out www.soigeneris.com for CarveWright Accesories.

    Home of the 'Carving in the Dark' back lit LCD kit!

  4. #14

    Default Replacing the Z-Motor Pac PDF

    This is in 3 separate PDF's because of forum size limitations. I broke the 1 mb PDF into 3 smaller PDF's.
    Attached Files Attached Files
    The 50-50-90 rule: Anytime you have a 50-50 chance of getting something right, there's a 90% probability you'll get it wrong.

    Do it on a Mac.
    Vietnam Vet '65-'66

  5. #15
    Join Date
    Mar 2008
    Location
    Massachusetts
    Posts
    16

    Default gear replacement PDF

    Hope this helps some....
    Attached Files Attached Files
    THIS IS WHAT I DO WHEN THE PROJECT COMES OUT RIGHT!!!



    http://i344.photobucket.com/albums/p...cing_kitty.gif

  6. #16
    Join Date
    Mar 2008
    Location
    Massachusetts
    Posts
    16

    Default lots more PDF's good luck

    -More PDF's
    Attached Files Attached Files
    THIS IS WHAT I DO WHEN THE PROJECT COMES OUT RIGHT!!!



    http://i344.photobucket.com/albums/p...cing_kitty.gif

  7. #17
    Join Date
    Mar 2008
    Location
    Massachusetts
    Posts
    16

    Default Pdf"s

    THIS IS WHAT I DO WHEN THE PROJECT COMES OUT RIGHT!!!



    http://i344.photobucket.com/albums/p...cing_kitty.gif

  8. #18
    Join Date
    Mar 2008
    Location
    Massachusetts
    Posts
    16

    Default PDF's

    THIS IS WHAT I DO WHEN THE PROJECT COMES OUT RIGHT!!!



    http://i344.photobucket.com/albums/p...cing_kitty.gif

  9. #19

    Default Machine won't run

    Ok. I hope I can describe my problem before my brain runs out of words. On the last several carves the cut motor has been speeding up and slowing down. I read several posts before where it was stated that their machine did the same thing, so I thought nothing of it. Well, the last carve I tried it started out fine, then about 3 minutes into it, it sounded like a car running out of gas. Going at what I would say a normal speed, and then it slowed way down, then speeded up, slowed down, and then stopped. The Y and Z motors (back and forth, up and down functions) where still operating. I called LHR and they had me do some things and it started (they were listening to it on the phone). It ran for about 3 minutes and started doing the same thing as before. They sent me a cut motor, still same as before( speed up slow down finally stop). Then they sent the little green circuit board ( I don't know what it is called). Still no cure. Now they sent me a power pac. No change, Only now it runs for about a minute and stops, everything else keeps on running. I am hoping someone who might have had this problem would know of a cause for this problem and offer a solution. Thanks Woodie

  10. #20
    Join Date
    Jan 2007
    Location
    NE PA USA
    Posts
    9,898

    Default

    The only thing left is a loose Right Side cover Switch....

    AL
    Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.

    Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074

    www.PoconoDigitalWoodshop.com

    www.AccountabilityTag.com


Page 2 of 5 FirstFirst 1234 ... LastLast

Similar Threads

  1. techniques or troubleshooting you decide
    By menewfy in forum Techniques
    Replies: 2
    Last Post: 01-28-2007, 01:27 PM
  2. troubleshooting guide in PDF Format
    By dspadell in forum CarveWright Machine
    Replies: 3
    Last Post: 01-15-2007, 10:15 PM
  3. Why can we not read the troubleshooting section???
    By shabang in forum CarveWright Machine
    Replies: 3
    Last Post: 03-23-2006, 09:19 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •