Just got my unit 3 weeks ago and this maybe a dumb question but for doing basic signs ( address's ) what type of wood gives the best finsh ( less sanding ).
Just got my unit 3 weeks ago and this maybe a dumb question but for doing basic signs ( address's ) what type of wood gives the best finsh ( less sanding ).
The question is not that simple.
You need to consider the carving to be made and the wood quality.
Here is a link to a chart of some of the basic woods, showing the ability to be carved.
http://forum.carvewright.com//attach...2&d=1205283058
The sanding question may depend upon the combination od wood involved, the sharpness of the bit, and the speed of travel across the wood. I use the "Optimal" setting as I load the memory card, which gives me a finer carve, resulting in less sanding. I stay away from Oak on any project where I use and raster pattern, due to the loose grain of that wood.
AskBud
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29
hi and welcome to the forum!
As Bud already stated, the answer is a bit complicated.... but to give you a few, I very much like carving in hard woods with tight grains such as maple, mesquite, cherry (though it burns a bit) and walnut. Most exotic woods can be carved quite nicely, but are pricy in larger quantities (rosewood, the ebonies, zircote, bubinga etc)
Less-hard woods or woods with an open grain can give you mixed results, but I've still found them to work well-- (mahogany, the oaks/pecan/butternut)
Traditional softwoods can be carved but will require either more care or some sanding (d fir, most pines, basswood, kauri, etc)
I hope this helped,
Lawrence
Generally speaking,,, Hard woods carve cleaner.. Pine gets a lot of what we call fuzzies... But There is the cost of hardwood verses pine.. I've carved lots of walnut and mahogany, both perform well, with very little sanding needed... I've carved various other hardwoods with very good results... Cocabola, bloodwood, maple, Jatoba, Bamboo... etc... But when it comes to basic stuff, I use plain old Pine... With a dremel an exacto knife and some sandpaper it cleans up pretty good... You can also burn the fuzzies with a propane torch, just don't over due it and char the wood... Then most of it easily shaves away with and exacto...
Mans Quest for knowledge,,, means he'll always find a way !!
There is also the option of a sanding mop to clean up your carves.
As well as, the quality setting you select.
CarveWright CX Packaged System - starting at $2000
CarversClub 1 Year Subscription - $150.00/year
Adv. Support w/out CC membership - $25.00/issue
CarveWright Community Forum - PRICELESS!
I agree with the wood mentioned, but would like to add Purple Heart very hard and very little clean up.
Leo
If you can find a source European Beech carves GREAT!
I love using cherry and walnut. I've even had good results with regular pine under certain conditions. With pine, you have to run the carve on optimal and your carving elements need to have draft on them. Any hard edges will fuzz up for sure. Oak works pretty good, but it does have kind of rough surface to it sometimes after a carve. For out door signs, I've used a lot of locally cut red cedar with centerline text and they turn out fine. Raster carves on cedar is kind of iffy though, tends to chip out a lot.
One wood that is often overlooked, that I like to use is aromatic cedar. It has good density and hardness and carves almost as clean as walnut. And it is fairly inexpensive. It can add a nice rustic quality to your work.