Page 1 of 5 123 ... LastLast
Results 1 to 10 of 65

Thread: Making Rotary Patterns

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Feb 2008
    Location
    Indian Lake, Ohio - Rts 33 & 235
    Posts
    3,967

    Default Making Rotary Patterns

    I'm starting to try my hand at making Rotary Patterns.
    I've had the jig since it was introduced, but have not used it until today. I wanted to scan my own model from the start. I have some ideas for chess pieces as beginning projects. I'll scan the models, apply to a MPC and prove they work well before I offer any patterns or MPCs. I'm finding little secrets that cause problems. I'll resolve them as I go along.

    So far, I've scanned the knight shown below and laid out the MPC. My first carve blew up half way through (saw dust jamb, I think). There is no forgiveness! I've got to build Ed's dust box (it fits in the rear, as the dowel turns that way rather than toward the front).

    I've scanned the King, Queen, and Bishop, but did not like the bulges from the hot glue over run. So. I'll trim the glue and re scan (It's about a 6 hour scan).

    Hopefully, in a few days, I'll have a good product!
    AskBud
    Click image for larger version. 

Name:	Scan of Rotary Knight.JPG 
Views:	367 
Size:	463.5 KB 
ID:	50181Click image for larger version. 

Name:	Rotary Knight MPC view.jpg 
Views:	343 
Size:	42.0 KB 
ID:	50182Click image for larger version. 

Name:	Scan of Rotary King Queen and Bishop.JPG 
Views:	363 
Size:	443.1 KB 
ID:	50183

    Just for kicks, before you ask! The tape on the scanning probe is my way to extend the life of the probe. The wire breaks down where it leaves the probe (from all the movement). Rolling it back to the chuck, and securing it there negates that particular problem. The other weak spot, for the probe, is the mini connector at the end of the probe and extension wire. It needs a touch of WD-40 before the start of each day. Perhaps, some day, LHR will resolve these two issues (they have a ticket on the need to change to a single cord, and address the exit point problem at the probe. In the mean time, be advised that you may get a second life from your probe, with a little tape (How is your stock Al?).
    AskBud
    Last edited by AskBud; 01-04-2012 at 11:54 PM. Reason: Probe note
    AskBud Downloads =>> CLICK HERE
    Lesson added
    7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"

    CW Vacuum Head Project =>> CLICK HERE
    AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons

    More than 1250 AskBud patterns
    vvv-CLICK BELOW-vvv
    http://store.carvewright.com/manufac...ufacturerid=29

  2. Default

    Now that is an awesome idea ....

  3. #3
    Join Date
    Jan 2007
    Location
    South East, Michigan
    Posts
    6,118

    Default

    I like It, -- I have a couple of Chess Sets made of plastic, plus a Lewis Set like the photo below,
    that are made of some kind of man made marble resin, that I would like to to scan and carve.
    Thanks for sharing you idea and info, please post more photos as you progress.
    Attached Thumbnails Attached Thumbnails Lewis Chest Set.png  
    Ken


    Ver 1.182 on XL Pro plus Ver 1.164 and 1.175 on Windows 7 Ultimate
    It Never Fails * Till * You Say It Never Fails

  4. #4
    Join Date
    Jan 2009
    Location
    Brighton, TN
    Posts
    929

    Default

    Bud,
    In the first picture the eyes are inset, in the second they are raised. Is this an illusion or is that correct? It has been a long night here so it could be my eyes!

    Looks good! I am working on some different stuff for the rotary jig as well. As soon as I get it finished I will post it.
    Steve

    Centerline
    Pattern Editor
    Conforming Vectors
    DXF Importer
    STL Importer
    2D Advanced Tools
    Designer 1.187, 2.007 and **NONE** on Mac OS 10.15.6 and Windows 10 via Parallels on Mac

  5. #5
    Join Date
    Feb 2008
    Location
    Indian Lake, Ohio - Rts 33 & 235
    Posts
    3,967

    Default

    Quote Originally Posted by SteveEJ View Post
    Bud,
    In the first picture the eyes are inset, in the second they are raised. Is this an illusion or is that correct? It has been a long night here so it could be my eyes!

    Looks good! I am working on some different stuff for the rotary jig as well. As soon as I get it finished I will post it.
    Yes, it is an illusion. The snap of the MPC can fool you, unless you move you angle of view left or right. It's like the picture of the old/young lady that you came across from time to time.
    AskBud
    AskBud Downloads =>> CLICK HERE
    Lesson added
    7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"

    CW Vacuum Head Project =>> CLICK HERE
    AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons

    More than 1250 AskBud patterns
    vvv-CLICK BELOW-vvv
    http://store.carvewright.com/manufac...ufacturerid=29

  6. #6
    Join Date
    Feb 2008
    Location
    Indian Lake, Ohio - Rts 33 & 235
    Posts
    3,967

    Default Rotary Chess Piece

    Here is the rotary scan I'm working on. I'll do one more proof on Wednesday 3/7/2012, before I submit it to the Pattern depot.
    AskBud
    Click image for larger version. 

Name:	ChessMan-1.JPG 
Views:	176 
Size:	449.8 KB 
ID:	51666
    AskBud Downloads =>> CLICK HERE
    Lesson added
    7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"

    CW Vacuum Head Project =>> CLICK HERE
    AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons

    More than 1250 AskBud patterns
    vvv-CLICK BELOW-vvv
    http://store.carvewright.com/manufac...ufacturerid=29

  7. #7
    Join Date
    Sep 2007
    Location
    Northern Colorado
    Posts
    7,962

    Default

    Looks like a good one Bud!!!
    RingNeckBlues
    My patterns on the Depot
    DC-INSERT It Just Sucks!

    Proven to out perform all others!
    Buy CarveWright
    Colorado FaceBook Users Group


    All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.

  8. #8
    Join Date
    Feb 2008
    Location
    Indian Lake, Ohio - Rts 33 & 235
    Posts
    3,967

    Default

    Quote Originally Posted by Kenm810 View Post
    I like It, -- I have a couple of Chess Sets made of plastic, plus a Lewis Set like the photo below,
    that are made of some kind of man made marble resin, that I would like to to scan and carve.
    Thanks for sharing you idea and info, please post more photos as you progress.
    I think I'll design my own Knight and Pawns, rather than trying to use the Lewis pieces (the knight is too wide, perhaps just a horse head).
    AskBud
    AskBud Downloads =>> CLICK HERE
    Lesson added
    7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"

    CW Vacuum Head Project =>> CLICK HERE
    AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons

    More than 1250 AskBud patterns
    vvv-CLICK BELOW-vvv
    http://store.carvewright.com/manufac...ufacturerid=29

  9. #9
    Join Date
    Jan 2009
    Location
    Brighton, TN
    Posts
    929

    Default

    OK.. You have me looking for a Old/Young lady now! I hate it when that happens!!
    Steve

    Centerline
    Pattern Editor
    Conforming Vectors
    DXF Importer
    STL Importer
    2D Advanced Tools
    Designer 1.187, 2.007 and **NONE** on Mac OS 10.15.6 and Windows 10 via Parallels on Mac

  10. #10
    Join Date
    Jan 2007
    Location
    Talladega Alabama
    Posts
    376

    Default

    Here she is... look from the top then the bottom.
    Attached Files Attached Files
    My Website: www.edscustomcarved.com
    Patterns or projects made, and uploaded by me, are not to be sold on E-Bay, EVER !.
    Thank You....

Page 1 of 5 123 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •