Got a Mr Heater Salamander/ Tube heater. Is it safe to use this in my workshop. It was a gift, and really heats up the shop nice, but I want to wake up tomorrow too. So is it safe for shop use????? Thanks
Got a Mr Heater Salamander/ Tube heater. Is it safe to use this in my workshop. It was a gift, and really heats up the shop nice, but I want to wake up tomorrow too. So is it safe for shop use????? Thanks
Not really the best.... It does burn up the Oxygen and put out hot Carbon Monoxide.... Short Term with ventilation your OK... But I would have a CO Alarm..... I went with Direct Vent LP Gas heaters... All the flame is outside... And no Back drafting Issues.
AL
Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.
Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074
www.PoconoDigitalWoodshop.com
www.AccountabilityTag.com
Well I am sure there will be opposition to my reply, but here I go! Before I put a wood stove in my shop I used kerosene heaters. I used 3 regular kerosene normally. The thing is have a window open for fresh air. I have a tube heater and it does work great!
Still it is important to have a fresh air source, I used the kerosene heaters for years before my wood stove. But it is up to you to use your heater!
Ike
I have run into problems with the drying of some finishes with heaters, puts a fine oil mist out with fumes .
Good heat but just watch it.
OLD SALT
Member CarveWright Start U team
Thanks for the replies. Ill keep an eye on it and get a CO2 detector. It sure does keep the shop warm, so ill try it for a while. If my wife tells me im acting dumber than normal I will know somethings up and Ive taken in too many fumes. JK
I do most of my finishing in the garage attached to the house so no problem there.
Thanks again.
Another must with these heaters is to keep them in optimum running order and use good fuel only. If you're getting a lot of mist out of them that could be unburned oil from improper air adjustment. Most of these will also burn K-2l oil but if you don't want your eyes to sting or your skin to itch stick with K-1 kerosene.
I use one of these in my garage when I am working in there to heat it up initially because it is quick. Then I switch over to a small propane radiant heater to maintain the temperature, which is much quieter!
Thinking about fumes, I have my dust collector directly vented outside my shop, and when checking on it I notice the air coming out was pretty warm, so hopefully that will keep the air circulated and any fumes in the shop to a minimum. Thanks again for all the replies.
You also have to ask yourself " where is all that hot air coming from out of the dust collector?" Your dust collector sucks air from somewhere and if it's not recirculated into the shop (by the way of a filter) it must be getting air from outside through vents in roof or cracks around doors, windows etc. Sounds like your dust collector( being exausted to the outside) is sucking all the heat out of the room. Just my thought. It's good your getting the fumes out , but you also need air to feed your heater .
Last edited by Dan-Woodman; 12-24-2011 at 10:29 PM.
1.187 Custom Woodworking for more than 40-years
Hope that it works out for you. I use a cat-propane heater myself. Kerosene heaters give my sinuses a fit, can't work around them for very long.
Sometimes I'm just totally underwhelmed!
Series "A" Craftsman with Carvetight.
My shop is in no way air tight. I also leave a window cracked while running the heater, so it should have plenty of fresh air to run on. Im not sleeping in there, at least not yet, so really just need it to keep the machine warm while running on these cold days.
BTW Dan, I see you are in Holden, Im right down the road in Sedalia.
Thanks for the replies and insight.