Junior Member
Help!!!machine not working!!
In middle of doing many project needed for chirstmas and I am having major trouble!!!
Load board, enter project, load bits etc and then NOTHING!!! It says its routing design but it is
not doing anything!!!! Have no idea what to do now!! I only have 26 hours of time on my machine.
Please help me sort through this!!! THANKS!!!!
In Memoriam
Trouble shooting
Do a test of a different small project, just to prove the machine is good or bad.Originally Posted by CLARKSCUSTOMDOORS
If the test project works, I would review the one causing trouble, re-load the card, and try it again.
AskBud
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29
Junior Member
Still does not work, does everthing up to the point of carving, then nothing!!!!
In Memoriam
Call LHR
Time to call LHR, while at your machine.
(713) 473-6572
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29
Junior Member
I agree with AskBud.....when I first bought my CW I had a similar issue, I re-formatted the memory card and reinstalled my project.....even sometime just clearing the job setup, rebooting the machine might help as well, that helped once with a board tracking problem that I had awhile ago.
Senior Member
Yes, re format the card and load the latest designer and load the projects and do it again.... Load the same no go project but also load a simple circle made into a carve region just to test the machine....
This problem could be a Thickness Problem.... Your board is too thick...
You can call me too, my number is on the bottom of my web pages below.
AL
Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.
Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074
www.PoconoDigitalWoodshop.com
www.AccountabilityTag.com
Senior Member
It sounds to me like the switches need cleaned ... check the cover switches. If the machine is going through all of the motions and the cut motor is not coming on it could be that simple.
You can press 00 (zero, zero) on the keypad and it will get you into the menu that lets you look at the status of all of the sensors on the machine. Arrow through to cover switch (I am not sure exactly what it says) open and close the cover and see if the status changes from open to closed. if one of them reads OPEN then clean them.
Senior Member
Wild guess that one of the cut motors wires could be out of it's conector or a bad cut motor brush...
flex shaft is bad?
Last edited by liquidguitars; 12-07-2011 at 10:35 PM.
Junior Member
THANKS all of you for the help, did contact Carvewright and hopefully I will up an running again soon!!!
Appreciate all of the HELP!!!!!
In Memoriam
What were the findings!
AskBud
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29
Posting Permissions
Reply With Quote