Results 1 to 6 of 6

Thread: Lookin'

  1. #1
    Join Date
    Dec 2008
    Location
    Wylie, Tx
    Posts
    1,680

    Default Lookin'

    Just lookin' to see if there might be a "shared" pattern of a Easter Bunny out there somewhere. I found a couple, but they look a little "rough" to carve and I'm still not that familiar with our Designer program to clean it up. Just askin'.......
    JerryB:.

    CarveWright START U Team Member
    Using 1.187, Conform, PE/Probe, Centerline.

    "Let's start sharing PTNs instead of MPCs so ALL SW versions can view & share"

  2. #2
    Join Date
    Jan 2007
    Location
    South East, Michigan
    Posts
    6,118

    Default

    Here's one I found in the Pattern Sharing Depot -- if you can use it.
    Attached Thumbnails Attached Thumbnails Free Easter Bubby 1a.jpg  
    Attached Files Attached Files
    Last edited by Kenm810; 11-07-2011 at 04:30 PM.
    Ken


    Ver 1.182 on XL Pro plus Ver 1.164 and 1.175 on Windows 7 Ultimate
    It Never Fails * Till * You Say It Never Fails

  3. #3
    Join Date
    Dec 2008
    Location
    Wylie, Tx
    Posts
    1,680

    Default

    Thank you sir. Much appreciated. Trying to make something for the "Blank" placard templates that we got in our POM. Maybe they'll be a selling point if I show it right. Doing a crafts fair sponsored by a Cowboy Church this coming weekend and trying to get ready for it.

    Quote Originally Posted by Kenm810 View Post
    Here's one I found in the Pattern Sharing Depot -- if you can use it.
    JerryB:.

    CarveWright START U Team Member
    Using 1.187, Conform, PE/Probe, Centerline.

    "Let's start sharing PTNs instead of MPCs so ALL SW versions can view & share"

  4. #4
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,314

    Default

    Quote Originally Posted by Kenm810 View Post
    Here's one I found in the Pattern Sharing Depot -- if you can use it.
    That one looks good enough to eat! Are you sure its not carved in Chocolate!?
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  5. #5
    Join Date
    Jan 2007
    Location
    South East, Michigan
    Posts
    6,118

    Default

    lol -- I have to admit, I did kinda lean on the Chocolate Flavor/Color button a little
    Ken


    Ver 1.182 on XL Pro plus Ver 1.164 and 1.175 on Windows 7 Ultimate
    It Never Fails * Till * You Say It Never Fails

  6. #6
    Join Date
    Dec 2007
    Location
    Yellville, AR 72687-0652
    Posts
    2,369

    Default

    Quote Originally Posted by chebytrk View Post
    Just lookin' to see if there might be a "shared" pattern of a Easter Bunny out there somewhere. I found a couple, but they look a little "rough" to carve and I'm still not that familiar with our Designer program to clean it up. Just askin'.......
    I have a few of them, will this one work?
    Attached Thumbnails Attached Thumbnails easter-bunny-2_DISP-cw.jpg  
    Attached Files Attached Files
    Using Designer Version 1.187
    Donations are always welcomed, thanks – send a check to my PO Box 652

    BJB
    PO Box 652
    Yellville,AR 72687-0652

    PM me for my e-mail address.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •