Page 2 of 8 FirstFirst 1234 ... LastLast
Results 11 to 20 of 78

Thread: Workshops & Preliminary Agenda

  1. #11
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,350

    Default Guest Speakers Announced

    We have confirmed guest speakers Michael Tyler, Doug Haffner & Jason Allen, but still invite others to join list.

    Interested in sharing your knowledge and expertise? Send email to marketing@carvewright.com
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  2. #12
    Join Date
    Dec 2009
    Location
    Yavapai Co, AZ
    Posts
    9

    Default

    Do you have start/stop times for each day for those of use still trying to figure out travel plans?
    Larry G
    V 1.187
    Centerline, Conforming Vectors, DXF Import, 3D Advan

  3. #13
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,350

    Default

    Not carved in stone, but we are planning on the workshops starting around 9:00 am and ending the day by 5 or 6 with an optional event each evening.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  4. #14
    Join Date
    Jan 2011
    Location
    Cedar Rapids, Iowa 52404
    Posts
    49

    Default Length of workshops

    Will each workshop last the entire day? Or will be be able to go to more than 1 each day?
    J.E. "Gene" Young, Sr.
    Allthingswood
    1929 Hughes Drive SW
    Cedar Rapids, Iowa
    CarveWright Start U Team Member

  5. #15
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,350

    Default

    Each workshop will last approximately 45 minutes. Depending on how many attendees, we may or may not have two workshops running at the same time. The trick on our end will be figuring out how many will attend which workshops, cause we know everyone will want to attend the guest speakers workshops. We have a large room and a smaller room. The good news is there is a retractable wall in between the two, so if we need to open them both up, we can.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  6. #16
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,350

    Default New Guest Speaker

    We are happy to announce we have added Jeff Birt to our list of Guest Speakers!

    Come see his workshop: P.E. with Coach Jeff (Get into shape with Pattern Editor)

    Learn the ins & outs of Pattern Editor:
    • Common Uses of PE
    • Using the Tools
    • 2d & 3d Techniques
    • plus more!
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  7. #17
    Join Date
    Dec 2008
    Location
    Wylie, Tx
    Posts
    1,680

    Default

    I'm assuming(hate that word) that it's OK to take our video cameras to our workshops right? There's going to be ALOT of information that's going to be put out in those 2 days and I just want to make sure that I can "rewind" later and make sure I understood everything.
    JerryB:.

    CarveWright START U Team Member
    Using 1.187, Conform, PE/Probe, Centerline.

    "Let's start sharing PTNs instead of MPCs so ALL SW versions can view & share"

  8. #18
    Join Date
    Apr 2009
    Location
    Snellville, GA
    Posts
    1,477

    Default

    Make that two requests for the ability to film parts of the workshop because I have only a B model CW and would like to be able to show potential clients the special features/improvements of the C Model via my iPad as video clips. Happy to share same with others after the Conference. We may even find others on the Team who are better at video editing than me.

    Shall we bring them? And I promise to not film after hours. What goes on in Texas stays in Texas (Well unless somebody gets up on the table for Karaoke).
    Fair winds,

    Capt Bruce
    Kinney deSigns http://kinneydesigns.us
    CarveWright START U Team Member.

    30 year USN SEABEE, the original Weapons of Mass Construction.
    Designer Ver 1.187 and 2.007, Ver.3.001 One 2009 B CW w ROCK and a 5th Year Anniversary C CW
    Rotary Jig, 2D and 3D, Tracing Probe, DFX and STL Importers

    .

  9. #19
    Join Date
    Dec 2008
    Location
    Wylie, Tx
    Posts
    1,680

    Default

    Quote Originally Posted by Capt Bruce View Post
    Make that two requests for the ability to film parts of the workshop because I have only a B model CW and would like to be able to show potential clients the special features/improvements of the C Model via my iPad as video clips. Happy to share same with others after the Conference. We may even find others on the Team who are better at video editing than me.

    Shall we bring them? And I promise to not film after hours. What goes on in Texas stays in Texas (Well unless somebody gets up on the table for Karaoke).
    I think that's a good idea. I have a "B" model machine as well. Hope we can all swap emails & share videos on what we see/learn at the workshops.
    JerryB:.

    CarveWright START U Team Member
    Using 1.187, Conform, PE/Probe, Centerline.

    "Let's start sharing PTNs instead of MPCs so ALL SW versions can view & share"

  10. #20
    Join Date
    Jan 2007
    Location
    Loomis, CA
    Posts
    74

    Default

    I can volunteer to do some video editing for posting on You tube or iPad use if you like. Another one of my many hobbies.
    Looking forward to the event! Registered have hotel, flights and car all booked!
    See you all there.

Page 2 of 8 FirstFirst 1234 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •