Page 1 of 4 123 ... LastLast
Results 1 to 10 of 37

Thread: Transportation

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,345

    Default Transportation

    TRANSPORTATION

    William P. Hobby Airport

    Distance from hotel: 13 mi.

    Drive time: 20 min.

    Directions: 45 South to exit 26 to Bay Area Blvd. (away from Mall)to Texas avenue, go left


    Transportation to and from Hobby Airport

    Type Typical Minimum Charge
    • Limousine 75.00 USD
    • Super Shuttle 15.00 USD
    • Rental Car 30.00 USD
    • Taxi 38.00 USD


    Houston Intercontinental Airport
    Distance from hotel: 66 mi.

    Drive time: 1 hr.
    Directions: 45 South to exit 26 to Bay Area Blvd.(away from mall) make a left into Texas Avenue



    Transportation to and from Intercontinental Airport

    Type Typical Minimum Charge

    • Limousine 100.00 USD
    • Super Shuttle 45.00 USD
    • Rental Car Call hotel for information
    • Taxi 75.00 USD




    Use this area for coordinating shared travel.
    Last edited by lynnfrwd; 03-11-2011 at 04:34 PM.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  2. #2
    Join Date
    Dec 2008
    Location
    Wylie, Tx
    Posts
    1,680

    Default

    any dates yet? I'm in for sure...
    JerryB:.

    CarveWright START U Team Member
    Using 1.187, Conform, PE/Probe, Centerline.

    "Let's start sharing PTNs instead of MPCs so ALL SW versions can view & share"

  3. #3
    Join Date
    Mar 2010
    Location
    Northern Utah
    Posts
    903

    Default

    Wish I could be there! You guys have a great time!
    Sometimes I'm just totally underwhelmed!
    Series "A" Craftsman with Carvetight.

  4. #4
    Join Date
    Aug 2008
    Location
    The Great Texas Gulf Coast
    Posts
    5,345

    Default

    Great!!! Yes, May 12 & 13th.
    CarveWright CX Packaged System - starting at $2000
    CarversClub 1 Year Subscription - $150.00/year
    Adv. Support w/out CC membership - $25.00/issue
    CarveWright Community Forum - PRICELESS!

  5. #5
    Join Date
    Dec 2008
    Location
    Wylie, Tx
    Posts
    1,680

    Default

    I'll be staying at the Days Inn & Suites close to the Hilton. Looking to see if anyone else will be staying there as well.
    JerryB:.

    CarveWright START U Team Member
    Using 1.187, Conform, PE/Probe, Centerline.

    "Let's start sharing PTNs instead of MPCs so ALL SW versions can view & share"

  6. #6
    Join Date
    Oct 2007
    Location
    Conroe, Texas, United States
    Posts
    1,550

    Default

    Jerry,

    What is the cost of a room at the Days Inn & Suites were you are staying?
    Happy Carving

    Robert D.
    rcdages

    CarveWright START U Team Member.

    The mightiest oak in the forest is just a little nut
    that held it's ground.

  7. #7
    Join Date
    Dec 2008
    Location
    Wylie, Tx
    Posts
    1,680

    Default

    Quote Originally Posted by rcdages View Post
    Jerry,

    What is the cost of a room at the Days Inn & Suites were you are staying?
    They are $52 per nite. Supposed to be real close to the Hilton from what I can see on the map.
    JerryB:.

    CarveWright START U Team Member
    Using 1.187, Conform, PE/Probe, Centerline.

    "Let's start sharing PTNs instead of MPCs so ALL SW versions can view & share"

  8. #8
    Join Date
    Dec 2008
    Location
    Wylie, Tx
    Posts
    1,680

    Default

    Just to kinda put it out there.... I'll be staying at the Days Inn & Suites about a mile away from the Hilton (according to the map). Arriving Wed at airport around 1pm and taking a cab to the hotel. It'll be a nice "brisk" walk to the Hilton so if anyone else is staying at same place, let me know via PM.
    See ya'll soon! Bring your cameras & camcorders! Be there or be square ! JerryB
    JerryB:.

    CarveWright START U Team Member
    Using 1.187, Conform, PE/Probe, Centerline.

    "Let's start sharing PTNs instead of MPCs so ALL SW versions can view & share"

  9. #9
    Join Date
    Feb 2008
    Location
    Fairview Heights, IL
    Posts
    6

    Default

    Greetings all,
    I'm flying in on Wednesday, supposed to arrive around 10pm, flying back home Saturday morning. Not sure on a car rental yet. I currently have reservations at motel 6, anyone else staying there and will gladly share car rental fees. Let me know.
    Brad Doyle
    Fairview Heights, IL

  10. #10
    Join Date
    Jan 2011
    Location
    Cedar Rapids, Iowa 52404
    Posts
    49

    Default

    Brad,
    Are you attending the conference in Houston? If you still need a ride from airport, I have space available. I will be arriving at Hobby about 11:45PM on Wednesday evening and leaving from the same airport on Saturday morning at 6AM. Let me know, as I would enjoy the company.
    J.E. "Gene" Young, Sr.
    Allthingswood
    1929 Hughes Drive SW
    Cedar Rapids, Iowa
    CarveWright Start U Team Member

Page 1 of 4 123 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •