Page 2 of 2 FirstFirst 12
Results 11 to 14 of 14

Thread: Pen box project

  1. #11
    Join Date
    Sep 2007
    Location
    Northern Colorado
    Posts
    7,515

    Default


    0 Not allowed!
    Quote Originally Posted by Rick P View Post
    Would I be able to make this box with my old version of Designer, 1.187, and my old Carvewright machine from 2008?? I have not been able to afford to do any updating of my machine, but it still works ok.
    Yes the MPC files Dick posted will open in 1.187 so you can do them. Just select the files, save them and open them.
    RingNeckBlues
    My patterns on the Depot
    DC-INSERT It Just Sucks!

    Proven to out perform all others!
    Buy CarveWright
    Colorado FaceBook Users Group


    All patterns and projects that I share on the CarveWright forum are for your personal carving purpose. They are not to be shared, sold or posted on any other web site without permission from RingNeckBlues Designs.

  2. #12
    Join Date
    Jun 2013
    Location
    Southeast Idaho
    Posts
    615

    Default


    1 Not allowed!
    It would be fun to start a thread for Christmas Gift Ideas with links to some of the older, very cool, stuff out there

  3. #13
    Join Date
    Sep 2008
    Location
    Cottage Grove, MN
    Posts
    434

    Default


    0 Not allowed!
    [QUOTE=fwharris;266509]Yes the MPC files Dick posted will open in 1.187 so you can do them. Just select the files, save them and open them.[/QUOTE

    Thank you !!
    Rick P -- ( Designer v.1.187 + Rock + Dust Devil)
    Carver in Minnesota
    "A government big enough to give you everything you want, is strong enough to take everything you have." Gerald Ford, 38th President

  4. Default


    1 Not allowed!
    I also make pens on my lathe, so this pen box is a great addition to my work.

    Quote Originally Posted by DickB View Post
    Here is my version of a pen box. I stole a few ideas such as the feet from another project that was posted somewhere on the forum, but sorry I can't find it now. The other project had a cover that opened 90 degrees. I like the idea, but I wanted a cleaner shape outside, so my box opens flat. You can of course easily personalize these projects with a name and an optional inscription on the inside.

    I made two versions. The project with the textured top was too big to upload whole, so I deleted the bottom to get it to fit forum limitations. You'll need to cut and paste from one project to the other to make it whole.

    If you build this project, here a a few suggestions:

    The hinges are readily available from Ace Hardware. After carving the project, remove top and bottom and trim the tabs. Lay top and bottom side by side, top upside down, with the hinge recesses touching one another, and top and bottom butting each other. Carefully install the hinges, making sure that the center line of each hinge lines up exactly with the edges of top and bottom. Now close the box, and use a sanding block to sand the front and sides of the box, top and bottom at the same time. This will ensure an exact fit. The design is such that even if you were off a little when installing the hinges, you can compensate with sanding and no one will know. Then, remove the hinges, and realign top and bottom. It may help maintain alignment to tape the front and side edges with masking tape. Now you can again use the sanding block to finish the back edges top and bottom.

    I found a quality Cross pen and pencil set on Amazon for less than $20, and got two sets to qualify for free shipping.

    The patterns were made with Paint.net using techniques similar to what I described here:
    http://forum.carvewright.com/showthr...om-sihlouettes

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •