When using carving bit lately and doing flat carvings the carving is rough like its cutting deeper and shallower its like small hills any ideas whats causing this
Junior Member
Carving not smooth help
When using carving bit lately and doing flat carvings the carving is rough like its cutting deeper and shallower its like small hills any ideas whats causing this
In Memoriam
If you attach the MPC, people may be able to eliminate that as a possible cause.Originally Posted by jbroussel
When using carving bit lately and doing flat carvings the carving is rough like its cutting deeper and shallower its like small hills any ideas whats causing this
What chuck are you using?
Is the a new machine or did you get it used?
AskBud
AskBud Downloads =>> CLICK HERE
Lesson added 7/15/2012 Titles begin with "2D-3D Build a Pattern-Part-3"
CW Vacuum Head Project =>> CLICK HERE
AskBud Home Page =>> CLICK HERE <<=PC lessons or CW lessons
More than 1250 AskBud patterns vvv-CLICK BELOW-vvv
http://store.carvewright.com/manufac...ufacturerid=29
Junior Member
It has done it on multiple mpcs the latest one is the clock in the project section the clock with the all the cuttings and also on the duck shelf the first duck shelf was smooth but the last one is rough
Junior Member
Sorry i havr the carve tight i have done other carvings on it no problem just lately its acting up
Junior Member
Check to see if the ztruck is still tight against the rail or any loose bit.
H. T.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Friends Don't Let Friends Use bad patterns!
For high quality patterns please email me or check out my website at: http://carvenow.com . Thanks!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Junior Member
ztruck is tight, i have tried my old bit an a new bit both do the same thing , in the carve regions....I just updated my software to the latest ver and the flash will do a small project today an see but i doubt its the software but i want to rule things out...........
Junior Member
ok may of found something the motor behind the ztruck is loose it feels like a bearing issue is that possible i have not took the cover off yet i checked the screw to the left to of it but thats tight. i can shake the motor a little when i do i notice that depending on the poistion the ztruck is not smooth going up an down,
Senior Member
Looks like you found it.... Screws to watch are the ones holding the motor to the machine and the 2 screws inside the gear box holding the gear box to the motor. You can adjust the meshing of the gears with the slotted holes.
AL
Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.
Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074
www.PoconoDigitalWoodshop.com
www.AccountabilityTag.com
Junior Member
ok fixed the problem with the motor after i replaced the motor now when I insert a bit and it travels to the right where that depth thing that pops out to check bit depth it does not go allthe way against to pop it out is thier a calibration or something else i need to do
Senior Member
When you put the top cover back on and plugged in the right side cover switch wires to the cut motor, you failed to push the wires back into the sweet spot in the corner.
What has happened is the Z Motor cooling fins are hitting the wires preventing the truck from reaching the bit flag....
That problem is a right of passage for each carve member.... We all do it.... We all learn....
AL
Favorite Saying.... "It's ALL About the Brass Roller"..... And "Use MASKING TAPE" for board skipping in the X or breaking bits.
Follow ME on Facebook http://www.facebook.com/pages/Accoun...50019051727074
www.PoconoDigitalWoodshop.com
www.AccountabilityTag.com
Posting Permissions
Reply With Quote