New LHR Chuck on the way

[AskBud]

Michael posted this 4/4/2010. It looks like LHR is close to releasing the new chuck.
AskBud
http://forum.carvewright.com/showthread.php?t=14996

[troydraper]

hey bud,, can you offer any advice , my carving bit is very loose in the quick release chuck, the bit is not loose in the holder, the problem is the holder is loose in the chuch after 23 hrs this is unbelieveable and has at least 1/8" movement at the tip of the carving bit,, whats your advice ,, new rock chuck or contact carvewright and try and get a replacement chuck ????? Thanks Troy

[AskBud]

hey bud,, can you offer any advice , my carving bit is very loose in the quick release chuck, the bit is not loose in the holder, the problem is the holder is loose in the chuch after 23 hrs this is unbelieveable and has at least 1/8" movement at the tip of the carving bit,, whats your advice ,, new rock chuck or contact carvewright and try and get a replacement chuck ????? Thanks Troy

Oh My!
Push is coming to shove!
I personally would not get the old QC version, now that the replacement is so near at hand.
I would call and see if they are ready to ship the new version. Push to speak with Joe if the answer is "no". The Rock is a good device, if the "wait time' is unknown.

I'm sure others will have some comments!
AskBud

[Sshanks]

seems like there is quite a bit of buzz about this new release from LHR..
I have yet to see any response or comment about it from them? (correct me if I am wrong... please)..

I think LHR should be commenting on this.. Once one of us goes to the Rock, it seems very unlikely we would ever switch back...
No comment by LHR makes the rumors seem like the release is too far out to wait.

Any thoughts?

[AskBud]

seems like there is quite a bit of buzz about this new release from LHR..
I have yet to see any response or comment about it from them? (correct me if I am wrong... please)..

I think LHR should be commenting on this.. Once one of us goes to the Rock, it seems very unlikely we would ever switch back...
No comment by LHR makes the rumors seem like the release is too far out to wait.

Any thoughts?

I know what you mean. However, Michael writes lots of documents for LHR, and appears to test new gear and features for them.

His sentence just above the "Bullet" list, in the thread below, is what prompted me to comment.
http://forum.carvewright.com/showpos...69&postcount=1
Quote: "The signs are about 15" x 8", carved (and cut out) on the 'Best' setting using the new, soon-to-be-available spindle/chuck from CarveWright".

Here is another link to a post by Michael:
http://forum.carvewright.com/showpos...10&postcount=7
AskBud

[lynnfrwd]

No comment by LHR makes the rumors seem like the release is too far out to wait.

No comment by LHR is probably because 20 hours ago when this post got started, we (LHR) were enjoying Easter with our friends and family. I hope you all enjoyed yours!

The new spindle is no rumor. It will be available soon. I am not going to jinx it by saying when, because sure as I do, it will get delayed and you guys would have my hide!

Whether or not to wait is up to each individual and their own timelines. If you have a project that has to be done by a certain time, then you need a replacement now. If not, wait for the new spindle.

[jgowrie]

good news!

[TerryT]

So, is the new spindle chuck going to come standard on new machines or is it going to be an "Addon" for a while?

[Digitalwoodshop]

hey bud,, can you offer any advice , my carving bit is very loose in the quick release chuck, the bit is not loose in the holder, the problem is the holder is loose in the chuch after 23 hrs this is unbelieveable and has at least 1/8" movement at the tip of the carving bit,, whats your advice ,, new rock chuck or contact carvewright and try and get a replacement chuck ????? Thanks Troy

Troy,

Just remember you MUST replace ALL worn Bit holders AT THIS TIME too.... Replace just the QC and install a bad Bit Holder and it will flop around in the new QC destroying it too.... In as little as one project....

Good Luck,

AL

[mtylerfl]

So, is the new spindle chuck going to come standard on new machines or is it going to be an "Addon" for a while?

Details are forthcoming...keep a lookout for official announcements, a Tips & Tricks, and more!

Note to All: If you have not subscribed to the CarveWright Corner Newsletter and the Tips & Tricks Newsletters, now would be a very good time to do so at http://www.carvewright.com/ and fill in the "Join Our Free Mailing List" form (if you are already signed up, there is no need to duplicate your entry). Joining automatically subscribes you to both the CarveWright Corner and the Tips & Tricks Newletters.