Search:

Type: Posts; User: badger2424; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds; generated 19 minute(s) ago.

  1. Replies
    17
    Views
    3,394

    Ordered, thanks guys

    Ordered, thanks guys
  2. Replies
    17
    Views
    3,394

    Yes you are right I didn't notice that and not...

    Yes you are right I didn't notice that and not much familiar with bearings but a regular 688rs should do the trick thanks
  3. Replies
    17
    Views
    3,394

    Thanks for your help, I will keep looking.

    Thanks for your help, I will keep looking.
  4. Replies
    17
    Views
    3,394

    Measured with caliper.mm is a digital reading,...

    Measured with caliper.mm is a digital reading, inches was manual caliper, and I got the same problem when I looked number up.
  5. Replies
    17
    Views
    3,394

    8688386882 this is the stationary tube in which...

    8688386882 this is the stationary tube in which the rubber conveyor belt rotates on
  6. Replies
    17
    Views
    3,394

    Finally found a number with jeweler visor 688RS

    Finally found a number with jeweler visor 688RS
  7. Replies
    17
    Views
    3,394

    Or 19.5mmx6.92mm with 8mm diameter hole

    Or 19.5mmx6.92mm with 8mm diameter hole
  8. Replies
    17
    Views
    3,394

    Bearing has no numbers but it's 3/4" tall, 1/4"...

    Bearing has no numbers but it's 3/4" tall, 1/4" wide with 5/16 diameter hole
  9. Replies
    17
    Views
    3,394

    X-drive conveyor stationary tube bearing

    Rubber Belt wasn’t tracking straight took it off an found I’ve got both bearings needed to be replaced on the in feed side of the stationary belt conveyor tube. LHR doesn’t sell these an was...
  10. Replies
    13
    Views
    3,325

    Thanks for all the response and you guys were...

    Thanks for all the response and you guys were right, dull bit. Sent the dull ones to Nelson, seems like a great fellow by the way, for $8 a piece. Can't beat that! Dian I do keep a bottle trend tool...
  11. Replies
    2
    Views
    5,496

    Just talked to this guy, Nelcyn, only charges $8...

    Just talked to this guy, Nelcyn, only charges $8 a bit and has other Carvewright customers. Sending 2 of mine and will let you know how it goes. http://www.nelcyn.com
  12. Replies
    13
    Views
    3,325

    Found a bit I didn't know I had, going to give...

    Found a bit I didn't know I had, going to give that a try an will get back to you. Thanks
  13. Replies
    13
    Views
    3,325

    Nope don't have one at the moment, guess I need a...

    Nope don't have one at the moment, guess I need a new one any how. Good excuse to get another. Will send the other 2 to your guy above to see how good he is. Thanks for the info.
  14. Replies
    13
    Views
    3,325

    No not the first, the pictures are from 2...

    No not the first, the pictures are from 2 different carves. Started 3 carves ago. Everything is tight bearing wise and don't know what to do to the encoder except check for dust, none there. Got me...
  15. Replies
    13
    Views
    3,325

    Can the 1/16 ball nose bit be sharpened?

    Can the 1/16 ball nose bit be sharpened?
  16. Replies
    13
    Views
    3,325

    Everything is tight, checked that an the bit is...

    Everything is tight, checked that an the bit is fairly new with about 60 hours on it. The wood is red oak which I have carved many times with no problems. Have taken the z truck off an put new rails...
  17. Replies
    13
    Views
    3,325

    Can't figure this out

    I'm having a roll-up problem where the Carver carved to the letters and then rolls the wood up at the edge of the letters Plus carving seems to be less detailed on optimal than usual. Seems to me I'm...
  18. Replies
    8
    Views
    2,537

    I use ash on a lot of sports signs, natural...

    I use ash on a lot of sports signs, natural finish with a stained oak trim and it works great. Very little sanding clean up.
  19. Replies
    12
    Views
    2,879

    Found a guy today who said he can make the y gear...

    Found a guy today who said he can make the y gear shaft. Supposed to get them (ordered 5) next week and will try them to see how they work and let you guys know. It's ridiculous that I now have 3 new...
  20. Replies
    11
    Views
    2,840

    Or Red set handle is engaged. Yep, I'm stupid and...

    Or Red set handle is engaged. Yep, I'm stupid and done that myself.
  21. Thanks Al.

    Thanks Al.
  22. Excellent bj, greatly appreciated!!!!!

    Excellent bj, greatly appreciated!!!!!
  23. Star of Life ptn needed, Thanks for replys

    Hey guys, anyone with the EMT star of life pattern? I can't get the snake right when I use the jpg. Thanks Tim
  24. Replies
    7
    Views
    3,617

    dltccf, welcome to our addictive world of...

    dltccf, welcome to our addictive world of carving!! Any problems come up, let us help, these guys know all about it.
  25. Replies
    10
    Views
    3,822

    Guido, just to let you know, when you use a back...

    Guido, just to let you know, when you use a back ground pattern, and merge additive, the back ground texture will also be on the pattern u merge. Gread for domes and such but mostly bad for back...
Results 1 to 25 of 146
Page 1 of 6 1 2 3 4