Search:

Type: Posts; User: BSarte; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    5,990

    Thanks, but I do not have the Centerline added to...

    Thanks, but I do not have the Centerline added to my CW program, on a budget right now.
  2. Replies
    4
    Views
    5,990

    Carving Fonts Final Results - Questions!

    Since being a newbee to carving and getting the final results I am looking for, have a few questions hopefully someone can guide me to get the results I am looking for?

    This is the first carving...
  3. Replies
    2
    Views
    4,616

    AHHH, maybe that is the issue, I have been doing...

    AHHH, maybe that is the issue, I have been doing "stay under the rollers" but will give that a try!

    I follow Carvewright Caraholics, GREAT page on FB. I do like the forums better, but like you...
  4. Replies
    5
    Views
    19,607

    Thanks! All very good information and as I tried...

    Thanks! All very good information and as I tried a few different techniques. The picture for this carving turned out pretty good (will post a picture once I get done with it finishing it).

    What I...
  5. Replies
    2
    Views
    4,616

    Jig - Issues 1st time

    OK, so I am a newbee and I have successfully carved 6 or 7 patterns so far. This particular pattern I am satisfied with the test carvings on pine and now I want to carve this in oak. I have a piece...
  6. Replies
    5
    Views
    19,607

    I see what caused the line, it is actually part...

    I see what caused the line, it is actually part of the picture......
  7. Replies
    5
    Views
    19,607

    Carving Images Issue

    Need a little help here from some of you who are more knowledgeable than me!

    So I imported a picture of my son and his wife in their Halloween costumes, looked pretty good to me, the only thing I...
  8. Replies
    12
    Views
    13,277

    Thanks! Being a newbee, I always have...

    Thanks!

    Being a newbee, I always have questions like that since I unsure about these things!
  9. Replies
    12
    Views
    13,277

    OK, so I decreased the depth to .2" and it made a...

    OK, so I decreased the depth to .2" and it made a considerable difference in how the bit carved those fine lines.

    Next issue I would like to understand? I have been getting some scrap wood from...
  10. Replies
    12
    Views
    13,277

    Thanks for the input! But back to my original...

    Thanks for the input!

    But back to my original question.....Is there a way in the software to define or select certain parts of an imported image?
  11. Replies
    12
    Views
    13,277

    Exactly my thoughts! I checked the pattern, both...

    Exactly my thoughts! I checked the pattern, both Draft & Bit Optimization were set to none. I set Bit Optimization to Best and Draft to Large. The Depth is set to .35" Would this be the best settings...
  12. Replies
    12
    Views
    13,277

    Here is the original image....

    Here is the original image....
  13. Replies
    12
    Views
    13,277

    Defining parts of an image imported?

    I have an image that I imported and it is one big aspect to the pattern.

    When I carve it I am using the 1/16" Carving bit, I set the depth to .35 which is what I want but when carving the pattern...
  14. Replies
    4
    Views
    5,493

    Thanks! I had been in the Favorites folder but...

    Thanks! I had been in the Favorites folder but the names did not correspond to the names shown in the program so I did not touch them. I was able to clean up my Favorites in the program!
  15. Replies
    4
    Views
    5,493

    Thanks for the reply! You explained how to get...

    Thanks for the reply!

    You explained how to get to the Favorites when in the program. Unfortunately before I realized what I was doing I saved several of the save images/patterns in Favorites and...
  16. Thanks for the info, appreciate it. I just...

    Thanks for the info, appreciate it.

    I just stopped at local place that does some woodworking and guy showed me a sign he made. It was basically an engraved words with the engraved part filled in...
  17. Replies
    4
    Views
    5,493

    Importing Image - Default File Location?

    OK, so I am a newbee to CW, have a question about where the software default file location is but first let me explain that I have a LAN at my home, several desktop workstations with 2 servers and a...
  18. Newbee to CW - Finishing techniques and supplies

    OK, I am a newbee to CW, have done some small projects so far but starting to try my hand at finishing (stain & paint).

    For finishing the carvings, I have a couple of signs that I made, sanding...
  19. How to tell what software version you need for a pattern?

    I an new to CW, have the basic version of software.

    Looking through the CW Pattern Depot and wondering if I can do some of these with the version of software I have?

    Is there a way to tell what...
Results 1 to 19 of 19