Search:

Type: Posts; User: opensores; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    28
    Views
    12,698

    It is a metric problem. I am not sure what...

    It is a metric problem. I am not sure what exactly fixed it, but I reset everything to standard, from the model to the CW settings, and everything worked! Yay for figuring things out.
  2. Replies
    28
    Views
    12,698

    Here you go... Not sure this is going to show...

    Here you go... Not sure this is going to show the problem though.
  3. Replies
    28
    Views
    12,698

    update, when I lower the depth below 1" and...

    update, when I lower the depth below 1" and change the bit from the 8th inch long, so the 16th inch carving bit, the error does not happen.

    I am wondering if possibly there is a problem...
  4. Replies
    28
    Views
    12,698

    Resurrecting this old one. I just...

    Resurrecting this old one.

    I just downloaded a new copy of Project Designer 2, and put this project into it for carving. The error I get is also 12288...

    Can I get some input on this? I...
  5. Thread: Probe error

    by opensores
    Replies
    15
    Views
    22,011

    I had to razor off some adhesive so I could...

    I had to razor off some adhesive so I could remove and clean the inside of the glass piece. Havent had an error since.
  6. Got another mold cut today. I have both the...

    Got another mold cut today. I have both the 3/16" and the 1/8" Long ball bits, and today I tried uploading a cut which was .875" deep, and had selected the 3/16" bit to do the job, but in measuring...
  7. The day was too long to update. I interupted...

    The day was too long to update. I interupted power during the cut twice, and it ended up taking longer than I wanted it to, but none the less, the route was successful. I will be running another...
  8. Here goes nothing....

    Here goes nothing. http://i1364.photobucket.com/albums/r724/jared_nelson2/molds/IMG_20140617_100412_284_zpsxivs7uak.jpg I'll update hopefully no sooner than 8 hours from now.
  9. Figured it out! Thank you again. Have you ever...

    Figured it out! Thank you again. Have you ever considered being a professional baby tortoise saver? I am going to take a look at the difference between a sliced cut, and a non sliced cut. Should...
  10. I don't fully understand that, however, now that...

    I don't fully understand that, however, now that I am this far, I am confident it will work. Are you saying that the boarder is still intact in the same way it was last time?

    I may have it...
  11. Dang, that is a trick for sure. That looks like...

    Dang, that is a trick for sure. That looks like it worked mostly. The only issue I see now is that when I select a feather, it doesn't show up in the rendering...
  12. Yes, it is still giving me a complete floor...

    Yes, it is still giving me a complete floor feather...
  13. No I haven't purchased that. .

    No I haven't purchased that. .
  14. For some damn reason, I can trim the edges, but...

    For some damn reason, I can trim the edges, but it wont save those changes to the pattern. I can save into a new file, either by exporting to a new STL (but the deep cut edges repeat themselves at...
  15. Exporting this as an STL is taking forever.

    Exporting this as an STL is taking forever.
  16. Ok, I am hot on the trail now! Thank you! Do I...

    Ok, I am hot on the trail now! Thank you! Do I need to have PE in order to trim these edges? It looks like in order to get the edits done in editor, after trimming the edges, I just need to export...
  17. So you used meshlab to turn it onto a surface...

    So you used meshlab to turn it onto a surface only? Then after importing you removed the zero with the wand? When you say trimmed the edge in PE can you explain that a bit more?
  18. ok, how did you do that?

    ok, how did you do that?
  19. Ok, this is officially my SOS call for help. I...

    Ok, this is officially my SOS call for help. I am not able to create a file which doesn't call for the perimeter of the board to be cut out. It is impossible... Here is the original STL file. ...
  20. Well, I received the carvetight on monday. Its...

    Well, I received the carvetight on monday. Its installed. Now I just have to get my tablesaw running so I can cut the 1.25" and .75" MDF sheets. I have the sheets. The 1.25" sheets will be used...
  21. I left a vmail at Carvewright, and recieved an...

    I left a vmail at Carvewright, and recieved an email telling me that my spindle was shipped out of the NYC factory, and will be re-shipped to me as soon as it arrives in TX in a week...
  22. Also, I plan on gluing after I carve.

    Also, I plan on gluing after I carve.
  23. A few points to hit. On each of these files, the...

    A few points to hit. On each of these files, the base piece will not have a floor feather, and won't be pierced. The upper slices will be cut out around the perimeter.
  24. Thank you. There are still some issues here, so...

    Thank you. There are still some issues here, so I am going to try to get to where you got on my end, to see what issues still stand.

    I do have meshlab, but haven't ever used it for anything...
  25. Since an STL file cannot be complete until it is...

    Since an STL file cannot be complete until it is a solid, boxed in shape, how do I remove the boxing, in CW? Before or after slicing? I have even tried slicing off the ends of the file, just to get...
Results 1 to 25 of 59
Page 1 of 3 1 2 3