Search:

Type: Posts; User: fwharris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    5
    Views
    86

    The head might not be level from the key pad end...

    The head might not be level from the key pad end to the bit plate end.
  2. The only thing I might try is to contact CW and...

    The only thing I might try is to contact CW and see if they might have any suggestions. They might want the project file to look at.
  3. Is that an upload to the memory card for doing a...

    Is that an upload to the memory card for doing a carving or loading it into the stl importer?
  4. In the preference settings increase the rendering...

    In the preference settings increase the rendering cache size up to at least 256mb, the higher the better. Under the help tab turn off "file preview".. If you have a large amount of patterns or a lot...
  5. During the import process you can see and change...

    During the import process you can see and change dimensions in the importer.

    Yes, very wide items are hard to get a scan on. As you have found out you need enough clearance for the probe to fit...
  6. Replies
    2
    Views
    96

    Maybe you can start a new or the one that just...

    Maybe you can start a new or the one that just finished and use the jog to position feature.
  7. Thread: Err-e03-0400

    by fwharris
    Replies
    2
    Views
    139

    http://support.carvewright.com/edge-detection-fail...

    http://support.carvewright.com/edge-detection-failure-message/
  8. Thread: Err-e03-0400

    by fwharris
    Replies
    2
    Views
    139

    The board sensor is faulting out when trying to...

    The board sensor is faulting out when trying to find the end or edges of the board.
  9. Replies
    2
    Views
    175

    Lori, The default bit for pattern type...

    Lori,

    The default bit for pattern type carvings like you have set up is always the 1/16" tapered ball nose carving bit. It can be seen in the "board settings"/"Pattern bit" settings. If a new...
  10. Replies
    12
    Views
    303

    When you do a "center both" it will put...

    When you do a "center both" it will put everything selected to the center of the board vertically and horizontally. Do one at a time and only center of the horizontal. Them position as needed.
  11. Replies
    12
    Views
    303

    Do a board measure on that last board. I bet the...

    Do a board measure on that last board. I bet the machine is seeing it just a little under your design size and that is why you are getting the scale message.

    I always design for my finished board...
  12. Replies
    12
    Views
    303

    Just do a board measurement without loading the...

    Just do a board measurement without loading the project.

    Are you saying YES to under the rollers or NO? it does make a difference.. see my comments from earlier...
  13. Replies
    12
    Views
    303

    It looks like you said YES to staying under the...

    It looks like you said YES to staying under the rollers. When you do that the machine will add 7" to your design board size. What was your design size? If it was 19" and you used a 26" board to...
  14. I run both versions on my lap top and no issues....

    I run both versions on my lap top and no issues. I did find out that the last version installed is the default version when you try to open an existing project file.

    I do not recall if this has...
  15. Yes you can delete and reinstall without loosing...

    Yes you can delete and reinstall without loosing your settings.

    You mentioned earlier about finding some bent pins, could that still be your issue?

    You can recover a stopped carving by...
  16. Thread: Gun Rack help

    by fwharris
    Replies
    4
    Views
    145

    You should be able to make one off of that...

    You should be able to make one off of that drawing or find one to purchase.
  17. Sounds like success is happening! An extra card...

    Sounds like success is happening! An extra card is handy. You can be designing and up loading while the machine is carving away.
  18. Thread: Gun Rack help

    by fwharris
    Replies
    4
    Views
    145

    Got to a gun store and look at and measure one.

    Got to a gun store and look at and measure one.
  19. That sounds like some progress was made. Lets...

    That sounds like some progress was made. Lets hope the updated firmware was your issue. To prevent damaging the card when you are taking the card out of the machine use some duct tape to make a pull...
  20. reformat the card and reflash the firmware. do...

    reformat the card and reflash the firmware. do the through the flash manager
  21. Replies
    17
    Views
    278

    Great job!

    Great job!
  22. Replies
    17
    Views
    278

    Yes the bathroom scale is probably the less used...

    Yes the bathroom scale is probably the less used tool for the machine and should be used each day/time when you are starting up a new session of carves.

    To increase the head pressure you can add...
  23. Thread: lost patterns

    by fwharris
    Replies
    2
    Views
    82

    Mitch, If you think you still have the...

    Mitch,

    If you think you still have the patterns on your computer try doing a search for them. If using windows use the search window that is usually at the bottom left corner of the screen.
    ...
  24. Replies
    17
    Views
    278

    When I said "designs" I was talking about the...

    When I said "designs" I was talking about the project you are making and the design elements you are placing on the board. All patterns and carve region areas including raster text style you can set...
  25. Replies
    17
    Views
    278

    What quality setting are you using when uploading...

    What quality setting are you using when uploading the project to the card? Are you setting the bit optimization to best on your designs? The best and optimal settings on upload will give you the best...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4