Search:

Type: Posts; User: allenjones; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Thread: Y-Bearings

    by allenjones
    Replies
    60
    Views
    4,838

    Y-Bearings

    They cost me $90 for the two. He told me the next ones will be cheaper since he has a blue print made up now. The first two where trial and error. Because I did not have a new one for him to go by. I...
  2. Thread: Y-Bearings

    by allenjones
    Replies
    60
    Views
    4,838

    Iíve had 3 to fail the large bearing has not...

    Iíve had 3 to fail the large bearing has not helped.....

    One failed at 85 hours bad large bearing.

    If I could find the large bearing size. I will be rebuilding at 100 hour until the plastic...
  3. Thread: Y-Bearings

    by allenjones
    Replies
    60
    Views
    4,838

    That looks interesting keep us updated. Sent...

    That looks interesting keep us updated.


    Sent from my iPhone using Tapatalk
  4. Thread: Y-Bearings

    by allenjones
    Replies
    60
    Views
    4,838

    Y-Bearings

    I had a local machine shop make me some metal shafts where the bearings wore the shaft down. So I have rebuilt 4 of my Y motors they are working great. I never had time to make them myself. They are...
  5. Replies
    3
    Views
    967

    Sometimes they work good but lower quality of...

    Sometimes they work good but lower quality of carve. Iím going to see why he changed the cutting angle of the carving bits after Christmas rush. They roll a very large burr or wood chip which makes...
  6. Replies
    3
    Views
    967

    I have tried Nelson, my bits did not work good...

    I have tried Nelson, my bits did not work good in spruce. Sent 18 to have reshaped. Back to using new bits. Nelson changed the geometry of the bits which worked for a few signs before they started...
  7. Replies
    9
    Views
    825

    Nice work!!! Sent from my iPhone using...

    Nice work!!!


    Sent from my iPhone using Tapatalk
  8. Replies
    17
    Views
    2,026

    Thanks for sharing this with us. I talked to...

    Thanks for sharing this with us. I talked to Nelson today. I'm sending him 20 bits Monday. He knows what he is doing. Can't wait to get the tools back.


    Sent from my iPhone using Tapatalk
  9. Thread: Y-Bearings

    by allenjones
    Replies
    60
    Views
    4,838

    Y-Bearings

    The new gearbox small bearing is the same size. On my last fail the larger bearing looks fine. But the shaft wore the same as the old gearbox. That's why I'm going to try a heat treat on them. The...
  10. Thread: Y-Bearings

    by allenjones
    Replies
    60
    Views
    4,838

    Y-Bearings

    I have the newer y gearbox. They wear out just as fast as the old gearbox. Just ordered two new gearboxes. Its shame we can not order the gear box shaft only. I run my machines 8 hours a day. 6 days...
  11. Thread: Y-Bearings

    by allenjones
    Replies
    60
    Views
    4,838

    Anyone have the Y bearing size for the larger...

    Anyone have the Y bearing size for the larger bearing and a good source. I have the smaller bearing just need the larger bearing that's in the newer y motor gearbox. Thanks


    Sent from my iPhone...
  12. Replies
    12
    Views
    1,144

    Thanks, it sure was a challenge, learned a lot. ...

    Thanks, it sure was a challenge, learned a lot.


    Sent from my iPhone using Tapatalk
  13. Replies
    12
    Views
    1,144

    I have finally finished this logo. They wanted it...

    I have finally finished this logo. They wanted it in red oak finished clear. Attached are the pictures of the logo is 30" x 30" x 1.5". Learned a lot on this project.83553835548355583556



    Sent...
  14. Replies
    12
    Views
    1,144

    help with friends school logo

    Thanks guys,

    I have been very busy on this logo. I appreciate the help with this but it came down to me learning more about the CW software, buying more software, working with the pattern in a...
  15. Replies
    12
    Views
    1,144

    help with friends school logo

    I am trying to carve this logo for a friend to donate to a school. It has been a nightmare. the letters need to be engraved. Any help would be appreciated. Attached is the file he gave me.
    ...
  16. Replies
    10
    Views
    1,200

    Thanks goes out to bjbethke and bergerud for...

    Thanks goes out to bjbethke and bergerud for helping me with my project. Attached is the design for the chicken coop.

    82840
  17. Replies
    10
    Views
    1,200

    better then mine. Thanks but I like this one...

    better then mine. Thanks but I like this one better and it is a larger file for converting. Can you help me convert it and what software do you use.

    Thanks for your help.
    AJ


    82830
  18. Replies
    10
    Views
    1,200

    Here is a clipart I like but am having trouble...

    Here is a clipart I like but am having trouble making a pattern from it.http://uploads.tapatalk-cdn.com/20161230/1f93a833d3715da15898872fc2cad530.gif


    Sent from my iPhone using Tapatalk
  19. Replies
    10
    Views
    1,200

    Not really, just needs a hen not a rooster. ...

    Not really, just needs a hen not a rooster.


    Sent from my iPhone using Tapatalk
  20. Replies
    10
    Views
    1,200

    lOOKING FOR HEN AND EGGS PATTERN

    I have hit a blank on designing a hen and egg pattern. This is for a chicken coop.

    thanks AJ
  21. Replies
    18
    Views
    2,856

    Carvewright will not sell me the gears they said...

    Carvewright will not sell me the gears they said I must buy the whole y motor assembly? Just another way for them to hold a gun to our head!!! They also informed me they reduced their inventory of...
  22. Thread: ffc cable

    by allenjones
    Replies
    10
    Views
    2,201

    Thanks just ordered Sent from my iPhone...

    Thanks just ordered


    Sent from my iPhone using Tapatalk
  23. Thread: ffc cable

    by allenjones
    Replies
    10
    Views
    2,201

    ffc cable

    Has anybody look in computer supply's for the ffc cable with any luck? Does anyone have the specs for the cable? I have found a lot of cables on eBay just need specs?


    Sent from my iPhone using...
  24. Thread: ffc cable

    by allenjones
    Replies
    10
    Views
    2,201

    I'm waiting for them also. Every time I need a...

    I'm waiting for them also. Every time I need a part Carvewright is out. This is very bad business.............


    Sent from my iPhone using Tapatalk
  25. Replies
    11
    Views
    1,300

    Nice work!

    Nice work!
Results 1 to 25 of 44
Page 1 of 2 1 2