Search:

Type: Posts; User: mikedhill1; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    1,560

    Thanks for the info everyone..

    Thanks for the info everyone..
  2. Replies
    3
    Views
    1,560

    Crank torque plate

    While putting a new board into my machine, the Crank Torque Plate broke in half. I assume that I can order a new one on Monday. I was just wondering if this is happening to anyone else? Also is there...
  3. Replies
    14
    Views
    9,841

    Thanks for the offer, but I can wait until...

    Thanks for the offer, but I can wait until monday, and I will order a few extra to keep on hand. I am just glad I was able to get it figured out so quickly. Once again you guys have helped me out...
  4. Replies
    14
    Views
    9,841

    Just disconnected the FFC cable from the truck...

    Just disconnected the FFC cable from the truck head and found a break in the wire right at the black plastic covering.
  5. Replies
    14
    Views
    9,841

    Ok I'm pretty sure it is the FFC cable. So how do...

    Ok I'm pretty sure it is the FFC cable. So how do I go about ordering a replacement cable?
  6. Replies
    14
    Views
    9,841

    The first time it happened was during carving,...

    The first time it happened was during carving, now it happens while measuring the board.
  7. Replies
    14
    Views
    9,841

    Z axis stall E06-0313

    I was carving a pattern when this error showed up. I turned the machine off, and back on, but the error was still there. I manually moved the truck back towards the control side of the machine....
  8. Thread: Fonts

    by mikedhill1
    Replies
    6
    Views
    2,089

    Thanks for the info guys

    Thanks for the info guys
  9. Thread: Fonts

    by mikedhill1
    Replies
    6
    Views
    2,089

    Fonts

    Is there anyway to add new fonts to the software?
  10. Thread: Cut Motor

    by mikedhill1
    Replies
    15
    Views
    4,053

    Well I got this figured out finally. It was the...

    Well I got this figured out finally. It was the micro switch that cuts the motor. The cover would close and activate the switch, ( but just barely) but as soon as the truck started moving, the motion...
  11. Thread: Cut Motor

    by mikedhill1
    Replies
    15
    Views
    4,053

    Thanks brdad, I think I'm going to wait until...

    Thanks brdad, I think I'm going to wait until tomorrow and call CW, see if they want me to send it in for repair or if they can walk me through a few things. Thanks everyone for your help, I really...
  12. Thread: Cut Motor

    by mikedhill1
    Replies
    15
    Views
    4,053

    Ok, I put the motor back in, checked the C1...

    Ok, I put the motor back in, checked the C1 capacitor, looked fine, checked the power supply, also looked fine, put everything back together, tried the pattern again, I put the bit in, the motor did...
  13. Thread: Cut Motor

    by mikedhill1
    Replies
    15
    Views
    4,053

    Ok, I checked both of the lid switches, they are...

    Ok, I checked both of the lid switches, they are fine, I removed the motor, and opened it up. I bought the machine brand new, it only has 25 hours on it. The motor has lots of wood dust inside, but...
  14. Thread: Cut Motor

    by mikedhill1
    Replies
    15
    Views
    4,053

    Thanks for the replies , I'm heading out to the...

    Thanks for the replies , I'm heading out to the shop to check these now, I'll let o\you in a bit..
  15. Thread: Cut Motor

    by mikedhill1
    Replies
    15
    Views
    4,053

    Cut Motor

    I received my machine on Wed of last week, and it has worked well since I got it until last night. While cutting a pattern last night, the cut motor rpms started to fluctuate. Before I was able to...
  16. Thread: New machine

    by mikedhill1
    Replies
    2
    Views
    3,252

    I'd like to, but it's goning to have to wait...

    I'd like to, but it's goning to have to wait until I can afford the trip
  17. Thread: New machine

    by mikedhill1
    Replies
    2
    Views
    3,252

    New machine

    Got my new Carvewrught last week, and have been learning on it at every opportunity. Have had nothing but fun so far..
  18. Replies
    602
    Views
    334,221

    Sticky: Hi, I just got my Carvewright last Wednesday, had...

    Hi, I just got my Carvewright last Wednesday, had a problem with a microswitch, which the staff walked me through, got me up and running, and I have been learning by trial and error ever since. Let...
Results 1 to 18 of 18