Search:

Type: Posts; User: onetexasoldman; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    955

    Thanks for the help got it working now have other...

    Thanks for the help got it working now have other problems
  2. Replies
    3
    Views
    955

    machine head not going down

    I am having a problem with the head not going down. I have taken the side cover off and where the handle screws on seems to be locked up.
    If I take the handle off the gear spins fine. Just the...
  3. Replies
    19
    Views
    3,411

    Changed the circuit board on the z-track head and...

    Changed the circuit board on the z-track head and now all is working fine. Now to call LCR and hopefully get the board and the board sensor so I can get my old machine running again.
  4. Replies
    19
    Views
    3,411

    ok changed out the whole Z-TRACK head assembly...

    ok changed out the whole Z-TRACK head assembly from old machine and it moves now and doesn't give me a code.
    carving great with the old machines Z-Track. Will now start switching circuit board and...
  5. Replies
    19
    Views
    3,411

    still the same

    still the same
  6. Replies
    19
    Views
    3,411

    I checked the FSC unplugged and plugged back. ...

    I checked the FSC unplugged and plugged back. When I turn the machine on it doesn't move at all. No up or down or back and forth
  7. Replies
    19
    Views
    3,411

    NOW went to carve and get the famous 06-0313. ...

    NOW went to carve and get the famous 06-0313. Checked everything all wires are plugged and tight. When I do the test on the Z it shows the code 06-0313 nothing happens. when power isn't on...
  8. Replies
    19
    Views
    3,411

    ok talked the wife into waiting to go to lunch. ...

    ok talked the wife into waiting to go to lunch. Switched out the sensors and now have 154 with a sheet of white paper
    Thanks for all the help AGAIN
  9. Replies
    19
    Views
    3,411

    Thanks but I know where it is just put a new one...

    Thanks but I know where it is just put a new one on the old machine. I took the sensor off cleaned it and it still only shows 25. tomorrow will trade the one with the old machine.
    If this is the...
  10. Replies
    19
    Views
    3,411

    white paper get 24 what do I have to replace it...

    white paper get 24 what do I have to replace it is still under warrenty only 80 hrs
    I do have a spare machine to take a part off of
  11. Replies
    19
    Views
    3,411

    light pine getting 20

    light pine getting 20
  12. Replies
    19
    Views
    3,411

    I have seen where to blow and now have done it a...

    I have seen where to blow and now have done it a couple times. Both my machines have the newer insert from Floyd. I have tried a couple different woods and also have tried the tape thing.
  13. Replies
    19
    Views
    3,411

    03-0400 Board sensor Problem

    I am getting check board sensor. I have a "C" machine and 63 hrs. Just finished a 15 hr carving and was starting a new carving and keep getting this error.
    I have blown out everything. Took the...
  14. I know LHR has the option to replace with rebuilt...

    I know LHR has the option to replace with rebuilt and sometimes the rebuilt parts are better but I just didn't have the time to wait seeing my other machine was down waiting for parts.
  15. Cut motor won't start

    OK after all said done, and talking to LHR this morning they wanted me to send in the motor so they could REBUILD it??? I replaced the motor with an old one I had after they told me that (didn't...
  16. That new insert you make sure is great hardly any...

    That new insert you make sure is great hardly any chips left after carving 4hrs
  17. I am having the same problem at 25hrs and 40 min....

    I am having the same problem at 25hrs and 40 min. Was carving and stopped said to clean rails (no code) did that and it started to carve but motor wasn't going. Checked everything you have...
  18. Replies
    22
    Views
    5,773

    I am now ordering a new switch.

    I am now ordering a new switch.
  19. Replies
    22
    Views
    5,773

    Thanks Jeff and no I don't have a millohm meter...

    Thanks Jeff and no I don't have a millohm meter and if I did wouldn't know how to use it anyway. Thanks
    Larry
  20. Replies
    22
    Views
    5,773

    I get the idea!!! I don't really like bypassing...

    I get the idea!!! I don't really like bypassing safety switches never had and never will. Just wanted to see if the motor would go on and didn't want to fry a board with my test. So now I know it's...
  21. Replies
    22
    Views
    5,773

    I'll check that again in the morning. It seems I...

    I'll check that again in the morning. It seems I have double checked everything but it won't hurt. Thanks for reminding me
  22. Replies
    22
    Views
    5,773

    I bypassed the switch running the wires from the...

    I bypassed the switch running the wires from the x board direct to the cut motor and it works. Even tho I checked the switch with the meter. Guess I will try my old motor now and see if it works. I...
  23. Replies
    22
    Views
    5,773

    what would happen if I bypassed the switch all...

    what would happen if I bypassed the switch all together.
  24. Replies
    22
    Views
    5,773

    tried the lamp thing the light doesn't come on...

    tried the lamp thing the light doesn't come on with the spinup when checking but does come on when it starts carving. This is the new motor!!!!!
  25. Replies
    22
    Views
    5,773

    tried that many times and just starts cutting...

    tried that many times and just starts cutting without the motor going. I am ready to thro this machine in the lake
    Have also checked the cover switchs again with my meter
Results 1 to 25 of 54
Page 1 of 3 1 2 3