Thanks Mike. Looks like I'll be adding that one with the cabin switch plate.
Thanks
ScottS
Type: Posts; User: ScottS; Keyword(s):
Thanks Mike. Looks like I'll be adding that one with the cabin switch plate.
Thanks
ScottS
Awsome Mike,
Where did you get that frame? I had seen something on here simular a while back
ScottS
Thanks Guys. I am going to check out a few cover when I go into the hardware store next week. I am not looking to sell these I am cutting right now. They are instead for something else in the works...
There are several guys here doing light switches and outlets covers. Is it necessary to put in a metal plate on the backside of the switch cover? I had put some store bought oak ones in my old house...
thanks Ken Its carving now and without the fireplace running.:-D Not suppost to get cold till Wednesday.:roll:
Thanks ScottS
I got It finally. It had the cutout hide. Thanks For your help Ken.Now to try the second cutout test. The 1st one had a little too big of holes and switch cutout. I tighten those up and added rear...
Ken Thanks I knew I just was not doing something right.
I do have another question. Why in my mpc does the bear switch plate not show the outline cutout on the back of the carving but It is...
I can't seem to get a cutpath around the bear and the lightswitch cover. Can anyone help?These are patterns I found here in the forums.
Thanks ScottS
You can however warranty the prob out, If it does not work, and you will get new unopened software and probe and sell that. I did that with one of my probes.
ScottS
Al funny that was the a same issue I had on my machine before I sent it back to Sears for warranty work. Although I clearly saw it touch the bit plate (with me flinging it out) then it would dimple...
Just as the title mentioned can the machine produce glue up able kitchen cabinets? Say a cabinet for dummies?
ScottS
I called LHR and am at 180 hours on my machine but passed the 12 months warranty. Guess I will now loose it to sears till after the holidays are over. I might have a used CC for sale soon.
Well thanks everyone. I went threw the machine again and check cables connections but did not see anything that stuck out. I did do allot more cleaning and now it almost brand new,including the...
I Changed the belt out and open up and clean cut motor,Set head pressureto 75. The machine will measure the sled ok BUt during bit engagement it errors out x axias 181 (this morning), y axias...
Well I cleaned it up and re-ran project . I did manage to get it start to carve 3 times but last 2 its errored out X axis 181. I did go into Panel and look at the x axis counts and when I rotated the...
Al Holy $hit your good. That belt on the muffler slide did rip a small section at @ 100 hours on the cut motor side. And yes it had rolled under itself on the panel side. I tore a section off and...
Ken I will look. The 3 x gears have been over the life of the machine. I have warmed the shed up to 68 F and reran board only to get a y axis error 299. I am gonna eat and pull it apart and clean it...
I have done some reading up and have 180 hours on my machine. I have replaced the x gears 3 times in those 180 hours. I can power down and move the belt both directions without binding. I have tried...
Thanks
I am looking to get into carving mantel now. We will see.I would think maybe 3-4 time more hours involve then the signs.
ScottS
Check out my website ans lmk if there is anything my wife or I could do for you. We live in Missouri and our prices refelct were we live.
Thanks
Scotts
www.chainsawartonline.com
Thanks again email is scottandsam1@centurytel.net.
Thanks ScottS
Thanks so much .That is exactlt what I wanted to do. Know how did ya do it?I played for hours to do that and could'nt figure it out.
Thanks so MUch
ScottS
This is the patterns I am working with . I wanted the marine emblem to pop like the dea does. I like the wood grain back ground and wanted it carved deep but it interfers with the marine emblem....
Can anyone point me to a How to combine all that? I need to put a wood grain background that will enable this emblem to be raised at the edges. Every time I do this it put the grain patten in the...
I have a few bits and pieces I tried to compile to make a marine emblem. I would like to make everything 1 pattern not separate pieces. Can anyone help.Also can you see anything that needs cleaned...