Search:

Type: Posts; User: fwharris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    9
    Views
    229

    How did the wiring look?

    How did the wiring look?
  2. Replies
    9
    Views
    229

    Look to see if there is any dust or particles in...

    Look to see if there is any dust or particles in the programmer. It could also be a loose wire connection at the programmer.
  3. Replies
    12
    Views
    211

    I am glad you got it to working. Work it several...

    I am glad you got it to working. Work it several times and then check your head pressure..
  4. Replies
    12
    Views
    211

    Not that I am aware of.

    Not that I am aware of.
  5. Replies
    35
    Views
    4,692

    Looking good!

    Looking good!
  6. Replies
    12
    Views
    211

    Maybe try adding more grease behind the clutch...

    Maybe try adding more grease behind the clutch plate. Remove the crank handle and with a small tipped screw driver work the grease behind the plate. After doing so crank the head up and down several...
  7. Replies
    2
    Views
    99

    Yes there is a way to see the depth of text or...

    Yes there is a way to see the depth of text or anything else on the display board. Move the mouse pointer over the area that you want to know about. In the bottom left corner of the designer screen...
  8. Replies
    12
    Views
    211

    When you put it all back together did grease it?

    When you put it all back together did grease it?
  9. Replies
    12
    Views
    211

    Make sure did not put any washers between the...

    Make sure did not put any washers between the spring and the clutch plate. The spring goes against the clutch plate.
  10. Replies
    11
    Views
    540

    If during the measuring process it could loose...

    If during the measuring process it could loose tracking with the brass roller and cause measuring/position issues. It is highly recommended to always stay under the rollers and use out feed support...
  11. Replies
    11
    Views
    540

    Are you using the 7" rule for staying under the...

    Are you using the 7" rule for staying under the rollers? Is your board being supported with extra out feed support?
  12. Replies
    2
    Views
    336

    They have said that the spring in no longer...

    They have said that the spring in no longer needed. I believe it was with the introduction of the CX model of machines.
  13. Replies
    2
    Views
    473

    Thanks for letting us know about Ken's passing. I...

    Thanks for letting us know about Ken's passing. I hope he has moved on to his next journey.
  14. Replies
    11
    Views
    1,796

    Possible I guess. Do the scan at a higher quality...

    Possible I guess. Do the scan at a higher quality setting to get the best results. You can always adjust the size in designer after you get it placed on the board.
  15. Replies
    11
    Views
    1,796

    It might be your pattern. This is what I am...

    It might be your pattern. This is what I am seeing with I do an outline and cutpath.. left side is squared and right side is not.
  16. Replies
    11
    Views
    1,796

    I am not sure what you are seeing off of the...

    I am not sure what you are seeing off of the board. Here is my view. Is there a reason you are making your board size so small? I would suggest going a bit bigger to insure it fits. How are you...
  17. Replies
    11
    Views
    1,796

    Are you doing this as a 2 sided carve like it is...

    Are you doing this as a 2 sided carve like it is in the file you posted? If so, Increase your board size it looks like one side is masking out the other side. When I hide the back side the front side...
  18. Replies
    15
    Views
    1,756

    Get that baby all tricked out! Looking forward to...

    Get that baby all tricked out! Looking forward to seeing your process!
  19. Thread: Board sensor

    by fwharris
    Replies
    1
    Views
    476

    Yes, they have started taking the glass cover off...

    Yes, they have started taking the glass cover off of the sensor. They keeps it from catching the dust inside and giving bad readings. I would hang on to the new one.
  20. Replies
    7
    Views
    1,643

    My machine is also an A version. Bought it in...

    My machine is also an A version. Bought it in 2007.

    At $450 you are in cheap. Doing the needed upgrades; CarveTight chuck, A907 Z truck and a dust collection attachment should be all that was...
  21. Replies
    3,314
    Views
    1,861,175

    Sticky: True not having an image to go with the pattern...

    True not having an image to go with the pattern (ptn) or project (mpc) is not very handy for anyone looking for something. The request has been made several times for people to do so. Beyond that...
  22. Replies
    7
    Views
    1,643

    I have not needed to make any repairs on my...

    I have not needed to make any repairs on my machine for several years, probably close to 500 hours. Just a quick clean and lube.
  23. Replies
    3,314
    Views
    1,861,175

    Sticky: That is correct. Not all of the patterns are...

    That is correct. Not all of the patterns are carve able. You are better off saving a link to this and go through one by one to weed out the bad and save the good. Save them outside of designer in...
  24. Replies
    1
    Views
    734

    It could be the pattern. Did you apply the bit...

    It could be the pattern. Did you apply the bit optimization to the pattern? Do you have a picture so that we can see what you are talking about?
  25. Replies
    35
    Views
    4,692

    No we can not! You missed a spot! ;)

    No we can not! You missed a spot! ;)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4