Search:

Type: Posts; User: Digitalwoodshop; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. The danger of not staying under the rollers then...

    The danger of not staying under the rollers then having the machine do cutting or carving within 3.5 inches of the end of the board is that while the board is only being held by one roller it can sag...
  2. Works Great.

    Works Great.
  3. Replies
    10
    Views
    287

    In my opinion what happened is that you installed...

    In my opinion what happened is that you installed the bits for a pre carve. When you went to install the bit a 2nd time the machine saw that the bit installed the 2nd time was a different length from...
  4. Replies
    6
    Views
    268

    Best to call LHR on this one.

    Best to call LHR on this one.
  5. I believe what I am going to do is buy two 2.2 KW...

    I believe what I am going to do is buy two 2.2 KW Water Cooled Spindles. I have the advantage that I do this as a business so it will be a tax deduction. Set one up on my small CNC and the other on...
  6. My latest idea is to skip the brushless router...

    My latest idea is to skip the brushless router and go with a Spindle... Either a Air cooled one or a Water cooled one... Replace the cut motor. Put the Spindle on the back of the machine. Sure it is...
  7. I used J-B Weld in October 2007.

    I used J-B Weld in October 2007.
  8. Replies
    5
    Views
    915

    That is an interesting question? I am using the...

    That is an interesting question? I am using the free software.

    Just a WAG... try a space bar before the first letter and a space bar after the last letter.

    AL
  9. On a very early "A" I saw a Magnet inside the...

    On a very early "A" I saw a Magnet inside the Spindle and a Circuit board on the back that picked up the motion. So it picked up speed at the motor and at the spindle... That spindle sensor ended...
  10. That is a very good question.... I do know...

    That is a very good question....

    I do know that to some extent the X Termination Board does control the speed of the Cut Motor... Never really understood how or why... We all know that after you...
  11. Not yet... But I am looking into using a Dewalt...

    Not yet... But I am looking into using a Dewalt Brushless Router with the slap on battery eliminator 120 volt plug. I see on some CNC Pages some guy is already playing with the project and used a 15...
  12. ALSO since you needed to tighten the Y Belt... I...

    ALSO since you needed to tighten the Y Belt... I would QUICKLY order some 685ZZ Bearings and make plans for some preventive maintenance and replace the two bearings inside the Y Gearbox. Having to...
  13. Replies
    5
    Views
    207

    If you dumped a pile of sawdust on the floor then...

    If you dumped a pile of sawdust on the floor then sucked it up with your shop vac you would get that same shock.. It is the sawdust flowing through the hose that makes the static.

    And yes, in the...
  14. Replies
    3
    Views
    226

    Before you change anything if it was me I would...

    Before you change anything if it was me I would carve the very same board again. Since it did not cut deep enough.

    I would pay attention to:

    1. Be sure the bit is tight enough and not sliding...
  15. Replies
    1
    Views
    117

    Thank You Tim for helping us to understand what...

    Thank You Tim for helping us to understand what has happened... You are the BEST !!!!!

    AL
  16. Replies
    63
    Views
    2,548

    ( The Older I get... The Better I WAS ) 20 years...

    ( The Older I get... The Better I WAS ) 20 years fixing Navy Fire Control Radars and Computers. Then off to Sony in 95 making picture tubes or CRT's. Was a Shift Mechanic for 12 hours in the middle...
  17. Replies
    63
    Views
    2,548

    I deleted my Power Supply Wire Rant. Joe is...

    I deleted my Power Supply Wire Rant. Joe is taking care of it.
  18. Replies
    63
    Views
    2,548

    Here are some pictures of Really BAD X...

    Here are some pictures of Really BAD X Termination Boards.... I believe some are caused by UN GROUNDED machines that build up STATIC ELECTRICITY on the Machine FRAME and ARC OVER taking out some...
  19. Replies
    63
    Views
    2,548

    Got the note... Thank You :) I believe it is a 2...

    Got the note... Thank You :) I believe it is a 2 Watt resistor. The Brown is NORMAL.... I believe the X Termination Board is GOOD.... When they FAIL... They BURN... I will post a 2nd reply with...
  20. Replies
    2
    Views
    153

    Tapered Boards are the leading cause of broken...

    Tapered Boards are the leading cause of broken gears. Tapered in Thickness.
  21. Replies
    7
    Views
    274

    Good JOB !!!! Everyone..... For the future,...

    Good JOB !!!! Everyone.....

    For the future, since every board is a different color... Use a piece of white copy paper on the board and crank the head down and measure the Board Sensor. A 156 is...
  22. Are you a member of the Facebook page? If not......

    Are you a member of the Facebook page? If not... Lots more Activity on that page... You might find someone parting out a machine...
  23. To clarify. I have been a owner since 2007. I...

    To clarify. I have been a owner since 2007. I had some early cracked front motors but they were both used and were shipped to me with the flex installed in the cut motor. This put undue stress on...
  24. I see the broken part is in the REAR of the Cut...

    I see the broken part is in the REAR of the Cut Motor. Honesty since 2007 this is the First one I have heard of... I have had the Flex End crack on a few cut motors. All were shipped with the Flex...
  25. Replies
    10
    Views
    492

    I like the Shim Idea posted above.. That is what...

    I like the Shim Idea posted above.. That is what I would do.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4