Search:

Type: Posts; User: cnsranch; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thanks Jerry

    Thanks Jerry
  2. Jerry.....I'm a little confused. I've always...

    Jerry.....I'm a little confused. I've always been under the impression that carbide shafted bits would slip in the CT adapters.....only use steel. Do you disagree with that?
  3. Anybody got a line drawing of the State of Missouri?

    Looking for one I can carve with the v bit.

    Thanks
  4. Replies
    22
    Views
    2,477

    Took my toolchest to The Woodworking Show in KC...

    Took my toolchest to The Woodworking Show in KC this weekend and entered it in the Project Showcase. Won People's Choice and Educator's Choice.
  5. Replies
    8
    Views
    871

    Finished with two weeks to spare! This is...

    Finished with two weeks to spare!
    This is actually a prop for my Daughter-In-Law's budding infant photo biz.
    Can't do a project without a little Carvewright action 😛
  6. Replies
    8
    Views
    871

    Thanks all.....got it figured out.

    Thanks all.....got it figured out.
  7. Replies
    8
    Views
    871

    Anybody got a wheel pattern?

    Building a cinderella carraige for the little ones. A wheel pattern like the pic below sure would save me some time.
    It will be approx. 10" in diameter.
    It can be flat in design - I can route the...
  8. Replies
    22
    Views
    2,477

    And the handles from Rockler.

    And the handles from Rockler.
  9. Replies
    22
    Views
    2,477

    I believe I got the hasps and hinges from Lee...

    I believe I got the hasps and hinges from Lee Valley and the corners from Gerstner. Don't have the info on the felt - just make sure you get "sized" felt.......this was 5/64ths.
  10. Replies
    22
    Views
    2,477

    By the way......no nails - all spline joints (29...

    By the way......no nails - all spline joints (29 of them) and dovetails for the drawers.
  11. Replies
    22
    Views
    2,477

    Fixed the pics - sorry.

    Fixed the pics - sorry.
  12. Replies
    22
    Views
    2,477

    Way too easy to build it right side up.

    Way too easy to build it right side up.
  13. Replies
    22
    Views
    2,477

    I'm not putting MY nasty old tools in it 😏

    I'm not putting MY nasty old tools in it 😏
  14. Replies
    22
    Views
    2,477

    No plans.......I found one on the Net that I...

    No plans.......I found one on the Net that I liked and started from there.
  15. Replies
    22
    Views
    2,477

    Sometimes a Little Goes a Long Way

    It's not a Gerstner, but I'll set it next to one any day......
  16. Replies
    7
    Views
    684

    Not bad for a 10 year old machine, huh?...

    Not bad for a 10 year old machine, huh?
    Oh.......repairs done in the last 10........
    1. Upgraded from original QC to CT chuck (I was one of the last QC's - due to my fault I finally shelled it...
  17. Replies
    7
    Views
    684

    Finished product......I'm happy with it - let's...

    Finished product......I'm happy with it - let's hope they are.
  18. Replies
    7
    Views
    684

    Thanks guys. I found one that I think will work.

    Thanks guys. I found one that I think will work.
  19. Replies
    7
    Views
    684

    Anybody Have a Nice Crucifix to Share?

    Hi, all.
    Mom in-law's assisted living facility has asked me to carve a crucifix for their weekly Rosary. I found a nice one when searching here, but the cross itself is pretty elaborate.
    If y'all...
  20. Replies
    2
    Views
    559

    Can't seem to navigate the site. I've been...

    Can't seem to navigate the site.
    I've been paying about 91 cents each for the 80 grit .75" disks.
  21. Replies
    2
    Views
    413

    Little airbrushing and a lot of Rustoleum 2X...

    Little airbrushing and a lot of Rustoleum 2X clear satin......
    Thanks for your responses......bjb, I wish I hadn't already carved it before asking.....your pattern's great.
  22. Replies
    5
    Views
    451

    Thanks Steve.....brdad was right - it's a flat...

    Thanks Steve.....brdad was right - it's a flat eye bolt.
  23. Replies
    5
    Views
    451

    Eye bolt! You da' man!

    Eye bolt! You da' man!
  24. Replies
    5
    Views
    451

    Non - Carvewright ID help needed.

    You all are the smartest bunch I know........
    Cousin's restoring an antique glider. Told him I'd help find some bolts.
    I know they're out there - but don't know what to search for.
    These bolts...
  25. Replies
    2
    Views
    413

    Has anybody painted this Rose Pattern?

    Hey all.......
    Did a sign for the first granddaughter's (Grace's) bedroom door a couple years ago.......she has a new baby sister, so here we go again.
    New one's name is Elizabeth Rose, so I...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4