Search:

Type: Posts; User: fwharris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Thread: lost licenses

    by fwharris
    Replies
    6
    Views
    160

    Did you loose everything on your hard drive? Did...

    Did you loose everything on your hard drive? Did you have anything backed up?
  2. Replies
    4
    Views
    123

    Yes I would upgrade to the CarveTight Chuck.

    Yes I would upgrade to the CarveTight Chuck.
  3. Replies
    4
    Views
    123

    What chuck does it have? I am guessing it is a...

    What chuck does it have? I am guessing it is a sand paper belt that needs replaced? CW does not sell them any more but there is another source for them..

    ask for material, Aluminum Oxide Open...
  4. Replies
    5
    Views
    140

    [QUOTE=Tractorman;272850]There are a few fonts...

    [QUOTE=Tractorman;272850]There are a few fonts that have different symbols - Webdings and Wingdings - how do you pick ďoneĒ?[/QUOTE
    You use the font just like any other font.
  5. Replies
    7
    Views
    268

    You should not post your software license info...

    You should not post your software license info and machine ID
  6. Replies
    3
    Views
    111

    Do a "save as" to see where the last project was...

    Do a "save as" to see where the last project was saved to.
  7. Thread: Tree Pattern

    by fwharris
    Replies
    12
    Views
    414

    Typically an image is hard to make it into a good...

    Typically an image is hard to make it into a good pattern. To many high and low areas to get evened out.
  8. Replies
    1
    Views
    121

    Yes I have used a drawing tablet with designer.

    Yes I have used a drawing tablet with designer.
  9. Replies
    1
    Views
    154

    The files are to be opened with Designer.

    The files are to be opened with Designer.
  10. You will probably get a better answer if you call...

    You will probably get a better answer if you call them.
  11. Replies
    4
    Views
    215

    The install bit position is when the truck is in...

    The install bit position is when the truck is in the center of the machine. Trying to move it to another location when it is asking for the bit to be installed could/might cause a stall error.
    ...
  12. Replies
    15
    Views
    937

    Things that should help, Increase your...

    Things that should help,

    Increase your rendering cache size in the preference settings.

    Disable file preview under the help tab.

    Try to minimize the number of pattern you keep in your...
  13. Replies
    15
    Views
    937

    Also increase the rendering cache size.

    Also increase the rendering cache size.
  14. Look in the shared pattern section. There is a...

    Look in the shared pattern section. There is a zip file for all of the states outlines.
  15. Replies
    7
    Views
    293

    Michael Tyler posted the info some time back. It...

    Michael Tyler posted the info some time back. It included the step over rate for each upload quality setting I think.

    Results for searching "step over"
    ...
  16. That is do to the size and profile of the bit. I...

    That is do to the size and profile of the bit. I do all of my edge routing on the router table, not the CW.
  17. Replies
    3
    Views
    164

    I believe it is for the size you set up for the...

    I believe it is for the size you set up for the project.
  18. Thread: Sanding

    by fwharris
    Replies
    3
    Views
    119

    Sanding mops, radial sanding disc, diamond burr...

    Sanding mops, radial sanding disc, diamond burr tool for the drimile, sanding sticks.
  19. Replies
    5
    Views
    228

    Instead of drawing four lines use the rectangle...

    Instead of drawing four lines use the rectangle tool.
  20. Replies
    3
    Views
    102

    Instead of drawing four lines use the rectangle...

    Instead of drawing four lines use the rectangle tool.
  21. Replies
    5
    Views
    228

    Can you post your project so we can see what you...

    Can you post your project so we can see what you are talking about with the "edge cut"?
  22. Just for clarification, patterns are what go on...

    Just for clarification, patterns are what go on the sides and top of the urn and a project is for how to make the urn box. Your urn in the pictures is probably the most common style/design that I...
  23. Are you looking for specific patterns?

    Are you looking for specific patterns?
  24. Henry, An urn is just a box for containing the...

    Henry,

    An urn is just a box for containing the remains. You can put any kind of patterns on the sides and top or the urn.
  25. Replies
    13
    Views
    397

    https://www.toolstoday.com/cnc-router-bits-and-ins...

    https://www.toolstoday.com/cnc-router-bits-and-insert-bits/solid-carbide-spiral-cnc-router-bits.html?diameter=823
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4