Search:

Type: Posts; User: Mike1; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Yamaha Roadstar

    by Mike1
    Replies
    7
    Views
    201

    That worked perfect, it looks great. Thank you...

    That worked perfect, it looks great. Thank you for your help Oscar.
  2. Thread: Yamaha Roadstar

    by Mike1
    Replies
    7
    Views
    201

    Is it possible to delete the square surroundings...

    Is it possible to delete the square surroundings and only keep the logo, using 1.187. I tried to do it when I imported it but it was the logo that deleted not the square box, even if I inverted it. ...
  3. Thread: Yamaha Roadstar

    by Mike1
    Replies
    7
    Views
    201

    It was a nice ride. I am at the other end of the...

    It was a nice ride. I am at the other end of the spectrum, cool sunny then rain. I know it will get better. Thanks again.
  4. Thread: Yamaha Roadstar

    by Mike1
    Replies
    7
    Views
    201

    Oscar, wow, thank you so very much. You are...

    Oscar, wow, thank you so very much. You are always there to help. Have you been riding? Today was my first ride, Canadian weather!!
  5. Thread: Yamaha Roadstar

    by Mike1
    Replies
    7
    Views
    201

    Yamaha Roadstar

    Any chance someone has this pattern. I did try to clean it up in Gimp and greyscale it but, no luck. Thank you.
  6. Thread: Corian Outlets

    by Mike1
    Replies
    2
    Views
    114

    Try this one....

    Try this one. http://candlestonegifts.com/candlestone-store/
  7. Thread: 60 v bit letter

    by Mike1
    Replies
    5
    Views
    177

    Click on Centerline in the text box area then...

    Click on Centerline in the text box area then *Conform* in the tool selection area.
  8. Thread: 60 v bit letter

    by Mike1
    Replies
    5
    Views
    177

    Highlight the words you want to use a *V* bit for...

    Highlight the words you want to use a *V* bit for then go to the *tool bar* and choose *Bit Select*, choose whatever bit you would like to use.
  9. Replies
    10
    Views
    444

    Great to hear, thanks for the update.

    Great to hear, thanks for the update.
  10. Replies
    10
    Views
    444

    Good luck Rick, we feel your pain..

    Good luck Rick, we feel your pain..
  11. Replies
    10
    Views
    444

    Did you try flashing the card and trying a...

    Did you try flashing the card and trying a different pattern
  12. Thread: Ontario Users

    by Mike1
    Replies
    2
    Views
    102

    Hi Duncan, I believe we spoke in the past....

    Hi Duncan, I believe we spoke in the past. Cornwall, On.
  13. Replies
    14
    Views
    663

    Very nice and thank you for sharing.

    Very nice and thank you for sharing.
  14. Replies
    8
    Views
    528

    Machine off, disconnect the flex shaft and then...

    Machine off, disconnect the flex shaft and then try moving the truck before doing anything else
  15. Thread: Y axis Stall

    by Mike1
    Replies
    4
    Views
    412

    Have you checked the cut motor brushes?

    Have you checked the cut motor brushes?
  16. Replies
    4
    Views
    330

    The same happened to me this week. In my case I...

    The same happened to me this week. In my case I was trying to carve a board that was about 7/16", it kept spitting it out . Changed board to 3/4" and it worked just fine.
  17. Thread: Litho Help

    by Mike1
    Replies
    6
    Views
    389

    It happens just after I put the cutting bit in...

    It happens just after I put the cutting bit in and it is checking for depth. I will try a different carve this weekend. Thank you.
  18. Thread: Litho Help

    by Mike1
    Replies
    6
    Views
    389

    Good morning, it happens just after I put the...

    Good morning, it happens just after I put the cutting bit in. It tries to set up, then Z axis error.
    Thank you.
  19. Thread: Litho Help

    by Mike1
    Replies
    6
    Views
    389

    Litho Help

    I keep getting a z axis stall each time I try to carve this pattern when it asks for the cutting bit. I am using a sled with at least 3.5" (7" rule), which I have used many time before. But this time...
  20. Thread: Growth Ruler

    by Mike1
    Replies
    8
    Views
    918

    Well, it did not work out very well for me. What...

    Well, it did not work out very well for me. What does every one use to seal the board before carving and then painting? I used 2 coats of Varathane then painted then planed and the paint still bled...
  21. Thread: Growth Ruler

    by Mike1
    Replies
    8
    Views
    918

    Cool, I just picked up a piece of clear pine. 1"...

    Cool, I just picked up a piece of clear pine. 1" x 6" x3/4 for $20.00 (I decided to go with 1x6). I just put two coats of clear finish on it and I hope to carve it tomorrow. Finish it sometime this...
  22. Thread: Growth Ruler

    by Mike1
    Replies
    8
    Views
    918

    Very nice. How much would this sell for in your...

    Very nice. How much would this sell for in your area? In my area, I would be lucky to get the cost of the wood.
  23. Thread: Buffalo Bills

    by Mike1
    Replies
    0
    Views
    312

    Buffalo Bills

    Anyone have a (vector) pattern of the Buffalo Bills logos they will share. Please and thank you.
  24. Replies
    17
    Views
    1,342

    Thank you all, for the education, and the kind...

    Thank you all, for the education, and the kind words. Talk about a love/hate for this machine ;-).
  25. Replies
    17
    Views
    1,342

    I now understand, the best money I have ever...

    I now understand, the best money I have ever spent ;). It is amazing how much I have learned on this one carve by changing it in every direction you could think of. Thank you so much to all for the...
Results 1 to 25 of 270
Page 1 of 11 1 2 3 4