Search:

Type: Posts; User: want2b; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    268

    Would you please post the hours run? Thx, Rick H

    Would you please post the hours run?
    Thx, Rick H
  2. Replies
    19
    Views
    743

    After seeing the final product it was obvious the...

    After seeing the final product it was obvious the layering was the way to go. Started on some Xmas gifts early, attached are 2 of 8 completed recently. One is oak background the other is sycamore....
  3. Replies
    10
    Views
    444

    Just an FYI update, got time to try a carve and a...

    Just an FYI update, got time to try a carve and a 1 1/2 hr one ran fine.
    Rick H
  4. Replies
    5
    Views
    180

    AL, You're out of my league with all the...

    AL,
    You're out of my league with all the options but one thing I found out by a fluke might help you if controlling the depth using a 'centerline' type text carve would help. I found that by...
  5. Replies
    3
    Views
    150

    Sounds like you've narrowed it down to one of the...

    Sounds like you've narrowed it down to one of the bearings frozen. I've had it happen and WD didn't help, had to bite the bullet. Reality, trying the WD shouldn't hurt, what have you got to lose....
  6. Replies
    174
    Views
    14,687

    Another beautiful project. I keep kicking myself...

    Another beautiful project. I keep kicking myself when I see these you post, just got to make some time.
    Thx for sharing, Rick H
  7. Replies
    10
    Views
    444

    Replaced the ribbon cable from the controller up...

    Replaced the ribbon cable from the controller up to the terminal board. First and hope the last time, quite a pain in the XXX. Anyway, stall error message gone. Haven't had time to do a carve to see...
  8. Replies
    10
    Views
    444

    I did try a different card, forgot to mention...

    I did try a different card, forgot to mention that earlier.
    Thx for the reply, Rick H
  9. Replies
    10
    Views
    444

    No difference in resistance, think you have hit...

    No difference in resistance, think you have hit it . Didn't think about that test, in my mind seeing the position numbers change during the check was enough. Didn't realise the processor would be...
  10. Replies
    10
    Views
    444

    Z Axis Stall 06-0313

    Started a project and the moment I selected the project the Z Axis stall appeared on the screen. The truck was in the center of the machine never moved, I did not hear any sound indicating a 'homing'...
  11. Replies
    5
    Views
    403

    As with CarverJerry, interested but need more...

    As with CarverJerry, interested but need more info, would like to have machine serial number so Carvewright can verify the machine.
    Rick H
  12. Thread: Latest projects

    by want2b
    Replies
    11
    Views
    558

    I agree, you should be very happy with the final...

    I agree, you should be very happy with the final product. Haven't had the nerve to try one myself but your project does make me want to make something that beautiful.
    Rick H
  13. Replies
    6
    Views
    347

    Just might make somebody think. Neat. Rick H

    Just might make somebody think. Neat.
    Rick H
  14. Replies
    3
    Views
    207

    I can't remember all the materials that are good...

    I can't remember all the materials that are good or bad but I know there is a problem with some melting and sticking to the bit.
    Just an FYI if you haven't checked it out. Many posts regarding...
  15. Replies
    13
    Views
    522

    Would short in the wiring to the sensor give that...

    Would short in the wiring to the sensor give that type of constant reading or go the other way to a low one?
    Rick H
  16. Replies
    7
    Views
    710

    Have to second all the previous posts. Really a...

    Have to second all the previous posts. Really a cool project, unique with a lot of thought.
    Rick H
  17. Thread: Text Question

    by want2b
    Replies
    12
    Views
    527

    I just have the basic 1.187. From the above post...

    I just have the basic 1.187. From the above post seems like the software does not recognise <CR> as a valid character when moving it to the wood. Work around seems like the quickest and easiest fix.
  18. Thread: Text Question

    by want2b
    Replies
    12
    Views
    527

    Just tried , type JUNK return JUNK return return...

    Just tried , type JUNK return JUNK return return JUNK and the view shows mine with a double spacing between my second and the third line of text. Didn't load & carve, just assumed the screen was...
  19. Replies
    174
    Views
    14,687

    A one of a kind box. He'll never have to worry...

    A one of a kind box. He'll never have to worry about seeing another plus it will be something personal from you.
    Rick H
  20. Replies
    22
    Views
    1,906

    A confirmation of what we already knew, it's a...

    A confirmation of what we already knew, it's a beautiful piece of craftsmanship.
    Rick H
  21. Thread: Unique clock

    by want2b
    Replies
    83
    Views
    8,866

    Gorgeous! I am absolutely astounded by what you...

    Gorgeous! I am absolutely astounded by what you create. Just figuring out the gears and layout on paper is a monumental task. Then doing the design for all the pieces to be cut by the carver blows my...
  22. Replies
    1
    Views
    159

    Cool looking sword. Thx, Rick H

    Cool looking sword.
    Thx, Rick H
  23. Thread: Signing out

    by want2b
    Replies
    22
    Views
    1,426

    Your contributions to this forum have helped many...

    Your contributions to this forum have helped many of us. Don't stop. Even if you aren't carving we still need your expertise.
    Thx, Rick H
  24. Thread: Lithophane

    by want2b
    Replies
    8
    Views
    999

    Beautiful project, lithophanes are my favorite....

    Beautiful project, lithophanes are my favorite. Have done several large ones but never thought about putting multiple pics on one carve.
    Should be a treasured item.
    Rick H
  25. Replies
    2
    Views
    493

    Like how it turned out. Maybe smaller or a...

    Like how it turned out. Maybe smaller or a different font would make the other fit?
    Thx for sharing,
    Rick H
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4