Search:

Type: Posts; User: fwharris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    3
    Views
    193

    I would check the head pressure.

    I would check the head pressure.
  2. Replies
    5
    Views
    2,118

    https://forum.carvewright.com/showthread.php?22785...

    https://forum.carvewright.com/showthread.php?22785-Table-top-finish&p=202258#post202258
  3. Replies
    3
    Views
    193

    You probably had a display message about scaling....

    You probably had a display message about scaling. It asked if you wanted to scale the project or load a new board. If you said yes to scaling it reduced the project size. Scaling is caused by the...
  4. Thread: ER20 spindle

    by fwharris
    Replies
    13
    Views
    535

    Check with CarveWright to see if they still sell...

    Check with CarveWright to see if they still sell this. It says discontinued but shows up in the store. It fits the square hole on top of the spindle.. OR you can grind down something to fit.
    ...
  5. Replies
    44
    Views
    5,712

    It should not be to long before you are out...

    It should not be to long before you are out cruising the neighborhood. Getting any requests yet?
  6. Replies
    7
    Views
    384

    Glad to hear you made the switch, thanks! With...

    Glad to hear you made the switch, thanks! With corian make sure you are using a good sharp clean bit. Even though you are using my attachment there will still be chips that get into the machine...
  7. Replies
    5
    Views
    348

    Greg, To attach a file to a post use the "Go...

    Greg,

    To attach a file to a post use the "Go Advanced" icon and the bottom right of a normal post. Once there scroll down to "manage attachments" to upload a file.
  8. Replies
    4
    Views
    822

    This is a great place to get started......

    This is a great place to get started... http://support.carvewright.com/
  9. Replies
    4
    Views
    822

    Welcome to the forum! Sorry to hear about your...

    Welcome to the forum! Sorry to hear about your Dad. Since you are just getting started you should begin with visiting the CW web site and their SUPPORT section. There you will find the Learning...
  10. I would first take out the Y motor and gear box...

    I would first take out the Y motor and gear box to verify that the bearings are bad and if the shaft shows any wear signs. You can order replacement bearings at this link or from other places like...
  11. Thread: Depth of cut

    by fwharris
    Replies
    5
    Views
    791

    You are welcome! Hey we both got it right!

    You are welcome! Hey we both got it right!
  12. Thread: Depth of cut

    by fwharris
    Replies
    5
    Views
    791

    Something like this? Each rectangle set at a...

    Something like this? Each rectangle set at a different depth.
  13. It might be loosing the Y position or feeling...

    It might be loosing the Y position or feeling some resistance. Make sure the Y rail and bearings are clean and lubed. http://support.carvewright.com/cleaning-the-y-and-z-rails/

    Check the Y gear...
  14. Replies
    5
    Views
    482

    Great job from both of you. I have a lot of the...

    Great job from both of you. I have a lot of the coin patterns but not the capped bust dollar.
  15. Replies
    5
    Views
    445

    Great! Looking forward to seeing some of your...

    Great! Looking forward to seeing some of your work with it.
  16. Replies
    8
    Views
    2,755

    That is a bad link. the forum is not running any...

    That is a bad link. the forum is not running any more... this is the page http://allcw.com/


    I found this by doing a search for "ai2mpc" using the quote marks. Several pages of discussion. I...
  17. Replies
    5
    Views
    445

    Take a look here maybe.. I am not sure if any of...

    Take a look here maybe.. I am not sure if any of these guys are still around or not...

    https://forum.carvewright.com/showthread.php?7070-Simple-vector-paths-in-AutoCAD-How-TO&p=52397#post52397
  18. It should work for the crank.

    It should work for the crank.
  19. On the main page of the forum scroll down to the...

    On the main page of the forum scroll down to the "on line tools" and there is a section to care and maintenance schedule. It will take you here....
    ...
  20. Thread: Bit question

    by fwharris
    Replies
    2
    Views
    702

    I would think you could, just know that the carve...

    I would think you could, just know that the carve area will be larger than the design size. I would suggest to carve in multi passes and not very deep per pass.
  21. Replies
    247
    Views
    67,833

    Sticky: Happy Easter to you Oscar.

    Happy Easter to you Oscar.
  22. Replies
    5
    Views
    912

    Cool car! Thanks for the share.

    Cool car! Thanks for the share.
  23. Replies
    4
    Views
    304

    If you have the pattern editor or sculptor you...

    If you have the pattern editor or sculptor you can edit the pattern you created when you imported the stl into Designer. Open up the pattern tool to show the patterns in your favorite list. Next,...
  24. Replies
    3
    Views
    288

    Can you show an example or a sample project that...

    Can you show an example or a sample project that shows this please?
  25. Replies
    9
    Views
    603

    How did the wiring look?

    How did the wiring look?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4