A friend asked if I could carve a coke bottle relief piece to replace a missing doot handle on a coke cooler (like you would see in a market by the registers) I thinking 2' x 7" x 3/4 . I have no...
Type: Posts; User: normd; Keyword(s):
A friend asked if I could carve a coke bottle relief piece to replace a missing doot handle on a coke cooler (like you would see in a market by the registers) I thinking 2' x 7" x 3/4 . I have no...
I wasn't thinking of using the CW but a key cutter or slotting saw with a bearing?? But the wedge of the dovetail bit is a good thought!
Got the board pretty good now I want a pocket on the back for the peg -no problem - except = how to run a slot on 3 sides for a cover to slid into. can't find a router bit to do it.
I do use a sled and allow about 1/4 in on each end+-.
Thanks All ; I learned a lot it works. I run one more in pine before I go to harder wood.
Norm
I'm pretty happy with design but some how it has ended up too close to the end of the board on one end . I am using .200 grind and would like to move everything .400 to the left. can it be done?
I tried several times and approaches to get a pattern from attached photo with poor results!
choppy or ugly carvings . Anyone help please
I am trying to design a cribbage board in designer .What are the best ways? My design is 3 rows of 5 holes in a box 1" x .5 then ? group it and copy and paste to get the long runs down the length...
I am familiar with both of those resources but the CW ones are basically Reading everything and Buds are great if you have a specific problem , what I need is video WITH audio covering designer use ....
I have real ready problems ,so I am looking for a video /multimedia how to a-z on cw designer . I have seen at one time a voice over of the cw pdf can't find it now>? is that the best thing or are...
Deerfield, NH
Thanks I need to make a run to rockler for t-track but I think I understand enough to get this thing made now. At the price of wood you'd think it didn't grow on trees!
Do the end blocks nee to be the same thickness as the project material? Your right I double 7 not 3 1/2 oops . thanks everybody for the help
Norm
I'm to cheap to keep throwing away 14 inches of board every project! Would using a sled stop this waste? If so ? Design and use help would be appreciated!
Normd
Nice Early spring day in Deerfield.NH
Due to buget I've gone with Dremel Stylus but will file the better stuff away for a time when I can spend more money!
Norm D
I have an older dremel with flex cable . what is the best unit for clean up work? corded or cordless? etc
Norm D
since last post ,replace "fcc cable" replace Zmotor pack and brain adn kill a month with now a total 70 + hours on the machine in more the 9 months. It has been back to them once and had several...
This morning I did more investigation and found that the vertical and horizontal ribbon cable supports were not snapped together. Which got me looking very close at the ribbon cable where it enters...
No ,I joined "the club" so far a very good investment. Talked with Omar last evening and expect a call back today.
Went through those on my own and with tech and with second tech still no call back from " Hi tech"
New error voltage flucuation and z-axis stall . Have talked to level 0 and level -1 techs for most of the day yesterday with no solution , waiting for next level tech to call me back (up to 24 hours)...
The z-axis was "lumpy" when push up and down it jerked ,so I disassembled it . One bearing had dirt in it I removed the seal and with air got it smoothed out . What if any lube should I put in...
I need to cut just the second side of the dish as the machine errored as started the 2nd side. Can anyone give me a file to cut this?
Normd
I think I got the stahl problem Fixed but since this happened just after flipping the board can anyone disect the file so it will just start on side two(the bottom side of the dish. It carved the...