Search:

Type: Posts; User: sw123man; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    579

    I'll try that as soon as I can find the...

    I'll try that as soon as I can find the time-thanks
  2. Replies
    8
    Views
    579

    yes I have the wrench but will have to wait until...

    yes I have the wrench but will have to wait until my next day off -working 6 days a week doesnt allow for too much free time.321 machine hours.thanks again for the input fr someone like me that isnt...
  3. Replies
    8
    Views
    579

    I tried readjusting the y belt that did not help...

    I tried readjusting the y belt that did not help .I can not move the y-truck at all.but sprayed wd-40 on the bearings and will let it sit overnight.thanks for the help. hope it will magically fix...
  4. Replies
    8
    Views
    579

    y axis stall e05-0303

    While finishing my last project I received the y axis error, now it is firmly up against the keypad. I had the brushes and bearings replaced about year and half ago and only have used the machine...
  5. Thread: US-Minnesota

    by sw123man
    Replies
    8
    Views
    2,379

    I'm in PIPESTONE

    I'm in PIPESTONE
  6. Replies
    4
    Views
    479

    found the code and finish carving thanks for the...

    found the code and finish carving thanks for the help;)
  7. Replies
    4
    Views
    479

    I dont have a code to put in

    I dont have a code to put in
  8. Replies
    4
    Views
    479

    ‎Registration needed

    I turn on the carvewright and on the display it states that ‎Registration is needed
    then when I hit enter it want me to enter an unlock code.I never heard of this does anyone know why it isdoing...
  9. Replies
    4
    Views
    384

    found the problem- the end of the bit had broken...

    found the problem- the end of the bit had broken off about 1/4 inch and wasnt long enough to be recognized
  10. Replies
    4
    Views
    384

    I recieved it right before it asks for the bit at...

    I recieved it right before it asks for the bit at the end of the measurement
  11. Replies
    4
    Views
    384

    Check correct board load

    I keep getting the check correct board load then abort or retry.I have tried blowing out the area loading different boards and different projects.any suggestions?
  12. Replies
    24
    Views
    1,284

    i think i've tried everything including replacing...

    i think i've tried everything including replacing the controller cover switch cable assembly.can anyone think of anything else?i'm at a loss
  13. Replies
    24
    Views
    1,284

    yes the white wire is to the center,have to work...

    yes the white wire is to the center,have to work rest of the week so i'll check for a pinched wire then
  14. Replies
    24
    Views
    1,284

    tried everything still come up the the close...

    tried everything still come up the the close cover error
  15. Replies
    24
    Views
    1,284

    i had just installed the y gear assembly

    i had just installed the y gear assembly
  16. Replies
    24
    Views
    1,284

    close cover error

    I now get a please close cover error when I try to do anything.did all the troubleshooting tips still nothing.any suggestions?
  17. Replies
    3
    Views
    310

    thanks the pictures helped alot ,head pressure is...

    thanks the pictures helped alot ,head pressure is fine just needed a little nudge
  18. Replies
    3
    Views
    310

    head will not crank down

    when I try to crank the head down it clicks I had the head up to replace the y drive now I think its verticle lock up.it states in the manual
    Vertical Lockup: Cranking the head beyond its highest...
  19. Replies
    2
    Views
    369

    it was the fc cable,it had pulled loose on one...

    it was the fc cable,it had pulled loose on one side.Thanks again for being so helpful
  20. Replies
    2
    Views
    369

    z axis stall err E06 0313

    another day another error- I cleaned the y and zrails like it shows in the video now when I select a project and hit enter it goes straight to the z axis stalls error.any suggestions?
  21. Replies
    10
    Views
    1,403

    Thanks everyone for the info-it helps alot

    Thanks everyone for the info-it helps alot
  22. Replies
    10
    Views
    1,403

    it is starting the carve then after a couple of...

    it is starting the carve then after a couple of passes it brings up the error
  23. Replies
    10
    Views
    1,403

    y axis stall e05-0303

    I;ve received this error a couple of times,each time there is a clicking sound right before it stops, any ideas on whats happening?
  24. Replies
    8
    Views
    1,116

    I think the card not being in is the problem,but...

    I think the card not being in is the problem,but if you still want to get rid of it my neice would love it at that price- she's always bugging me to use mine
  25. Replies
    18
    Views
    1,446

    matthews paint has a line of paint that you might...

    matthews paint has a line of paint that you might be close to what your looking for
Results 1 to 25 of 105
Page 1 of 5 1 2 3 4