I'm too far to help you sorry.
Put your mpc in here so people can see what you are looking for
Type: Posts; User: brouv; Keyword(s):
I'm too far to help you sorry.
Put your mpc in here so people can see what you are looking for
That is AMAZING
Nut just the concept but the quality of the piece.
Good job.
Maybe one day, I will have enough time to do something like that.
Thanks michael
I will try tonight
will keep you posted
I live in Simpsonville SC (15 miles south of Greenville). I'm in the Upstate. At the opposite side of David in SC.
Had the machine for a while but my 2 kids takes a lot of my time
Forgot to...
I will post my latest mpc tonight but right now the only question I have is about the option to pick on the machine when I'm prompt with Center On Board, Jog To Position, or Place On Corner in order...
I searched for a similar thread but couldn't find it. Sorry for the duplicate.
Will check the plate and try the dime.
Thanks
Benoit
I got a small crash last night (Bit adapter came off - not locked oupssss) but didn't break anything I can see. I was able to carve after.
But if I ask the machine to measure the thickness of my...
Thanks again Michael,
I have no issue with the mpc nor the carving. I know I'm looking for the hard way. I did one last night using the 2 mpc concept (one with the flip vertically) and they didn't...
Good point
But if I wanted to do it that way, which option should I use ?
Ikea has something like that but not this nice.
Good job
Guys
I'm coming back with my project.
So I have my 2 files done and no issue
I cannot get the 2 cut align on the board.
when the machine ask me where to cut. Should I align to center, end or...
Ok now that make sense.
I didn't know you could do that.
Will give a try.
Thanks again and sorry for not getting it sooner
Benoit
Ok so new I have my 2 mpc (one cut to 0.6 and the other one to 0.9)
I still cannot get the tab
Do you think I can use some masking tape on both side during the second carve to keep the letter...
In the past, I was using winrar to compress (when I needed to compress and make it fit on floppy disk). You could tell it to split the compress file in different files. You just had to tell it how...
ok but if I do that when I do the second mpc with the 0.6 (since I already have the 0.9 releave behind), the letters will not be held by anything right ?
So they will break the tool
Benoit
I...
I'm sure I'm missing something but since my board is thicker than 1", I cannot use the cutout option therefore I cannot have the tabs
40001
Benoit
Do you have the flex all the way in ?
Make sure the square shaft is going into the truck all the way. If you have the ball, the clip to keep the ball and the flexshaft with the groove, everything...
Thanks Alan
I will have to try because I cannot see it right now in my head.
So to summarize, do the first one up to .9 (for example). Make a new mpc with the flip in the back and create the .6...
I was ok with that but how do I make sure the letter don't fly in the machine because I won't have any tabs to retain the letters ?
I had the same issue due to a new computer and without calling LHR, I couldn't do anything. Alex was kind enough to help me but I noticed that on the website, in the account info, you cannot use the...
Okay guys,
I have a challenge and I need your help to see how I can do it.
I'm trying to make a personnalize stool with my son first name in it.
I know how to do it with a 1" piece but not with a...
I had a 228 X axis error last night for the first time.
My board was long (6 feet) and even with the supports, the belts didn't like it.
I remove the gear cover and didn't see anything wrong with...
Thanks
I looked every where and couldn't find it in any menus
Sorry for the stupid question
Guys
I couldn't find an answer using the search engine
I noticed that the user manual for the software is mentioning that there is a tool " Trim Tool to trim intersecting line segments" in the...
Right
The flower peddle stuff wore out because of my unexperience with the qc
waiting for my new qc from LHR