Search:

Type: Posts; User: Digitalwoodshop; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Great Price. I will post it on the Facebook page...

    Great Price. I will post it on the Facebook page for you.
  2. Replies
    7
    Views
    830

    So no Sand Paper Belts.... CX. Another...

    So no Sand Paper Belts.... CX.


    Another option I found once.... The 4 smooth rails the whole head rides up and down on with the hand crank. I had tracking problems and found the screws in the...
  3. Replies
    7
    Views
    830

    Do you have Sand Paper Belts? They roll under on...

    Do you have Sand Paper Belts? They roll under on the keypad side. Very hard to see. It will cause Tracking Errors as the folded over belt raises the board off the tracking roller AND drive the...
  4. Replies
    19
    Views
    2,853

    The Pitch of the 18 pin FFC Flat Flex Cable is...

    The Pitch of the 18 pin FFC Flat Flex Cable is finer or closer together and thinner than the 14 pin.

    If you put a 14 pin with it's wider pitch or thickness into a 18 pin socket the wider 14 pin...
  5. Replies
    26
    Views
    2,137

    Good Job !!!!

    Good Job !!!!
  6. Replies
    26
    Views
    2,137

    You will have to delete the back side in Designer...

    You will have to delete the back side in Designer then run again.

    There is a Facebook group too for sometimes quicker answers.

    Don't give up, you will master this... It will be fun.

    Look at...
  7. Replies
    26
    Views
    2,137

    Lets address the two issues. First is the...

    Lets address the two issues.

    First is the tracking roller issue. Maple is very hard and very smooth. We recommend a strip of masking tape on the bottom of the board so the brass roller has...
  8. Replies
    19
    Views
    2,853

    Sorry to hear about your 18 pin cable. Due to...

    Sorry to hear about your 18 pin cable. Due to it's thinness it would let conductors snap inside the plastic leading to many problems from the bit driving into the board and jamming, Air Carves,...
  9. When you inspect your machine always be on the...

    When you inspect your machine always be on the lookout for FFC Cables that have any sharp bends in the moving part. It makes the bend or kink bend in a small area leading to failure. Like a piece of...
  10. Replies
    3
    Views
    1,123

    Welcome. Also join the CarveWright Facebook Page...

    Welcome. Also join the CarveWright Facebook Page too for quick help as you work through this first project. And get to know the machine.

    Good Luck,

    AL
  11. Replies
    13
    Views
    1,534

    Interesting problem..... Also you could spell out...

    Interesting problem..... Also you could spell out the month and a number for the date.
  12. Rick H posted above that if you buy a new...

    Rick H posted above that if you buy a new controller from LHR that they will program in your serial number. Is that correct?

    If so, then it must be done through that DB-25 port. ...
  13. Rather than buy a new controller... Another...

    Rather than buy a new controller... Another option is to send your controller and card to LHR to test... It costs.... But I don't think it is the Controller... I think it is a card issue.

    I...
  14. Replies
    4
    Views
    765

    If I was doing this I would go with a similar...

    If I was doing this I would go with a similar single board sled like I use to cut out plastic tags. Except I would add side rails as your litho will remove material in depth and the side rails will...
  15. Replies
    12
    Views
    1,538

    Wow, So sad for you... Tragic Loss...

    Wow, So sad for you... Tragic Loss...
  16. Replies
    601
    Views
    136,946

    Sticky: Welcome, This is a great place to search and...

    Welcome, This is a great place to search and learn. Be sure to join the two Facebook Pages.
  17. I will post this question on the Facebook page. I...

    I will post this question on the Facebook page. I don't remember the answer.... You have to enter the board thickness even though it is on the sled.
  18. Replies
    2
    Views
    1,430

    I will post this on the CrveWright Facebook page.

    I will post this on the CrveWright Facebook page.
  19. I am all talk and no action.... Did not build the...

    I am all talk and no action.... Did not build the Vacuum sled yet. Found 1/4 inch double stick tape made it easier, I was cutting 3/4 inch in strips so it is easier....

    I still have not opened...
  20. Here I show a Circuit Board Bit and a Roto Zip...

    Here I show a Circuit Board Bit and a Roto Zip 1/4 to 1/8 inch adapter. Don't use the Roto Zip bits in the CW as they are able to BEND as they are used for Drywall and thin board. The holder works...
  21. LHR gave me a Tip years ago that I use all the...

    LHR gave me a Tip years ago that I use all the time to cut sheet Fiber Plastic. You set up your Vector lines. I do not use tabs as I use 1/4 inch strips of double sided tape to hold the cut tag. I...
  22. Replies
    3
    Views
    670

    Also could have Centering the object turned on.

    Also could have Centering the object turned on.
  23. Replies
    1
    Views
    541

    Much more activity on the Facebook Page. You...

    Much more activity on the Facebook Page. You might get a quicker answer. There is a pattern section here. But I have not looked at it in Years.... Just watch out for the guy on eBay selling pattern...
  24. Replies
    3
    Views
    2,074

    Floyd will chime in shortly but I believe you...

    Floyd will chime in shortly but I believe you need to run the STL through a program to make it smaller first then use it in Designer.

    And you would likely get a quicker reply on the Facebook page....
  25. That is almost $3K. Post your location, it might...

    That is almost $3K. Post your location, it might help.

    I just took delivery of my 12th machine yesterday. $300.00 and $96.00 shipping. It is perfect but has a QC and a broken sand paper belt.
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4