Search:

Type: Posts; User: cjones; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    867

    Only a few days until the Houston Users Group...

    Only a few days until the Houston Users Group meeting. I have sent out the e-mail with directions for those who have showed interest. If you did not receive it, please send me an e-mail to...
  2. Replies
    6
    Views
    867

    I am getting an e-mail ready to send to all those...

    I am getting an e-mail ready to send to all those who have showed interest in getting together on April 27th. If you have not yet e-mailed me that you would like to be apart of this, please send me...
  3. Replies
    6
    Views
    867

    To everyone who has shown interest in the CW...

    To everyone who has shown interest in the CW Users group get together, we have set a date. April 27th starting around 9:30 to 10:00. The general area if you want to look it up is the intersection...
  4. Replies
    2
    Views
    400

    Help with cut path

    I am doing a pierced carving of a pattern and want to clean up the edges after it has completed the carve part. When I setup the cut path, how should I set the offset from the original carving. ...
  5. Replies
    6
    Views
    867

    I am working with Robert Dages and Bryan Weldon...

    I am working with Robert Dages and Bryan Weldon to get a local Houston area users group together. Several people at the conference noted they were interested in coming if one was started up. Sorry...
  6. Replies
    2
    Views
    222

    Z-Axis and Y-Axis errors

    Since mid December, I have been getting both Z and Y axis errors. I did a couple license plate size signs for a customer and, well the first one came out properly. The second came out offset, See...
  7. Replies
    2
    Views
    634

    Makes sense. MDF 1/2" is slightly smaller then...

    Makes sense. MDF 1/2" is slightly smaller then the 1/2 pine I used. I will try and place something under my board and see if it make a difference.

    Chris
  8. Replies
    2
    Views
    634

    Z Axis Stall Err E06-0324

    Need some assistance. I was trying to do a carve yesterday but was getting the error above. Here is the setup I had:

    I use a 3/4" think piece of plywood for my sled/jig board. I have equal sets...
  9. Michael, really like this months project. Do you...

    Michael, really like this months project. Do you know when it will be distributed. I have a show this weekend and was hoping to get a few made before then.
  10. Replies
    7
    Views
    636

    I believe I know exactly what you are referring...

    I believe I know exactly what you are referring to. I got mine July last year and it started having similar problems. I had to take it in for some other warranty repair and they found that...
  11. Replies
    5
    Views
    594

    Thanks Steve. I got the project done with the...

    Thanks Steve. I got the project done with the one Oscar was able to clean up. The only problem I had when it was completed was the lines breaking due to I forgot to add ant draft to it. Other then...
  12. Replies
    5
    Views
    594

    Thanks Oscar. I will try it out later today and...

    Thanks Oscar. I will try it out later today and see how it works. Not expecting great detail but my Mom would like a little so as others can tell what it is.

    Chris
  13. Replies
    5
    Views
    594

    Need assistance in ncleaning up a pattern

    I am trying to get a pattern cleaned up but have gotten it about as good as I can. Can anyone here see if they can do any better. Attached is the .MPW file, .JPG file and a picture of one I have...
  14. Thread: Head Pressure

    by cjones
    Replies
    4
    Views
    751

    Head Pressure

    When I checked the head pressure on my CW, it is reading between 92 to 102 +/-. I followed the direction on how to lower it by adding grease to the clutch area but it is still reading high.

    What...
  15. Replies
    7
    Views
    830

    OK, Try this one. ...

    OK, Try this one.

    https://www.dropbox.com/s/v8e6cah6h43kuwb/Scheduled%20Maintenance%20Worksheet%20CW.zip?dl=0
  16. Replies
    7
    Views
    830

    Let me know if the link does not work properly.

    Let me know if the link does not work properly.
  17. Replies
    7
    Views
    830

    Question. In the 100 hour scheduled maintenance,...

    Question. In the 100 hour scheduled maintenance, the schedule states to clean the X-Drive gears. How many go to the trouble of opening the X-Drive assembly area when it will most likely need...
  18. Replies
    7
    Views
    830

    Thanks Michael, I will have to find where I put...

    Thanks Michael, I will have to find where I put them. I has been awhile since I found them and am not sure where I put them. The CW runs no problem without it but as soon as I do, I will post a pic.
  19. Replies
    3
    Views
    1,135

    Here is one of his patterns I have already...

    Here is one of his patterns I have already carved. All I have to do is complete the finish and put mirror in the back.
  20. Replies
    7
    Views
    830

    200 Hour Maintenance

    I finally reached the 200 hour mark on my machine on Thursday. I am going out to do Maintenance on it this morning.. I took the maintenance schedule CW came up with and put it into Excel and...
  21. Replies
    3
    Views
    1,135

    Facebook Group with lots of FREE .STL files

    Anyone looking for some free .STL files in 3D, joing this Facebook group,3D models for cnc. Vitalie Diaconu is an amazing artist and this group, all his designs are free. He has another group...
  22. Replies
    2
    Views
    544

    I have all of the free one but do not yet have...

    I have all of the free one but do not yet have the DXF Importer. The downloads come with the .SVG, .JPG, .AI files. I just finished coverting a JPG over and it looks pretty good.

    Next purchase,...
  23. Replies
    2
    Views
    544

    Site for DXF files

    I came across a website selling DXF files. They have a starter pack with 250+ in it for free plus a few other free ones. They look like outstanding work on the creators part.

    Here is the...
  24. Replies
    3
    Views
    501

    Thanks Steve. I am currently using the SealCoat...

    Thanks Steve. I am currently using the SealCoat mixture as per Michael, 50/50 with DNA. This seems to help before I start to apply finish.

    I usually apply 2-3 coats of stain until it is what I...
  25. Replies
    3
    Views
    501

    How many coats of stain

    I was wondering, how many coats of stain do most of you put on a piece before applying the clear coat? And then how many coats of poly clear coat should be applied. As for the Poly, do you prefer...
Results 1 to 25 of 119
Page 1 of 5 1 2 3 4