Search:

Looking more closely at the discontinuity, it seems to be related to the diameter of the particular section of the tower... which leads me to suspect a rendering error, possibly in writing to the...

Lined up the bit with the grooves on the frame (had to adjust the off-keypad side a fraction) and ran the alignment 3 times to make sure it was getting good rotary offsets. Since the displacement is...

I did my first rotary carving yesterday, and almost everything came out the way I expected except for the left-right meeting on the "back" of the carving.

Here is the design file in Project...

Using the Clip Carving: Exclusive did it!!! Thank you everyone who responded or thought about the problem!

43977
Baron Richard

I am not using any Merger Control, as I said, using the Addition and Subtraction do not resolve the issue.

Try it your self, inverted designs seem to be handled differently in the software.

I...

I am trying to carve 2 crossed swords (purchased Patterns) inverted to make a mold. Unfortunately no matter what depth or height setting I use, the crossing is not coming out right. The shallower ...

Thank You!! The sensor check showed that the machine was not getting any input from the vertical movement of the cutting head and from that I was able to determine that the wire harness for the...

I just replaced the Z axis motor with a warranty replacement and upgraded the sandpaper belts tot he rubber belts on my refurb machine I bought in June.

When I go to start up the calibration...

>If your quick change starts to wobble while carving you will need to check the quick
>change turn power off Then check the qc from the outer of the jacket wiggle the outside
>to see if it's bad...

I had to replace the Quick Chuck and ordered a replacement on 10/27 because the set screw inside finally worked it way loose and came out in the middle of a project... Due to other failures on the...

Well I decided to put the existing sensor back in while I wait a week for the new sensor to arrive, I'm now getting a reading of 102... better, but still not as good as what I've seen posted. But...

Took the board sensor out to clean it (getting readings of 88-92 with a white sheet of paper on the board) and can see a little dust in the sensor pit. When I tried to clean it out with a little...

Is there a way to sort the Pattern Depot by "Add Date" so I can see what has been added most recently? Sifting through dozens of pages trying to notice the 1 or 2 new items is very tedious and not...

Chicagoman_35

Where are you getting 1/2" Lexan? I have been searching the central Ohio area and the thickest I can find is .118".

I was thinking of using the CW to cutout customized templated...

Sorry, but currently there isn't a way to break an "outline" created object. I've been looking for a way to do that for months, and the only thing to do is zoom in really close and then create a...

Is there a way to cut and make a tool path out of an outline? I have a PNG pattern file I have imported that is a rather complicated set of curves and I want to cut a 1/8"x1/2" deep line around one...

When I create a layout that has several pieces with a common center, is there a way to get the designer to show the offset of either just the center, or the outermost object to I can actually see the...

If all the new bits are going to Sears, where are they going? I checked on the web and at my local (large) Sears and both systems said there were no bits or accessories available at this time!! I...

Is there a way, other than redrawing from scratch, to rotate a spline shape 90 degrees in Designer? I have a shape I laid out in designer upright so I could make sure the proportions were right, and...

I've been dead in the water for 6 days with the homing flag error waiting on the update (that the Bard thought was supposed to be out last friday...)

Grrr, I'm gonna start chewing on some of this...

I found that creating a JPEG from CorelDraw 12 tended to dither the edge of the transition to add visual appeal on the screen. To get around this I now export as PNG (Portable Network Graphics) file...

You owe me a bakers dozen of the new Washington dollars coins then. :-)

The flag being out of place would be problem if it would not show blocked even when homed on either the Z of Y flag... my...

Wow, is this new file size limit restrictive! Hope you can make out the little bitty image I was able to upload (19.5kb??? limit )

Here is the picture I mentioned in my email about the homing...

I'm having a similar problem with a shape I created: I started out with a spline for the handle, copy, pasted, flipped left->right for the other half and moved so that the bottom vert's linked, then...

As a user with a down machine waiting on a Z pack, PLEASE!! Return your old one to LHR so they can rebuild it and ship it out to those of us waiting!! :cry: :cry:

I have been down for 2 weeks...