Search:

Type: Posts; User: mobident; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Thread: texture issue

    by mobident
    Replies
    4
    Views
    1,117

    Level looks good - Flats are level with casting...

    Level looks good - Flats are level with casting and no binding on raising the head
  2. Thread: texture issue

    by mobident
    Replies
    4
    Views
    1,117

    texture issue

    I haven't used the textures too much over the years so need a bit of input!
    I ran a large panel that uses the checkers2 texture and the horizontal definition of the squares faded out across the...
  3. Replies
    10
    Views
    3,426

    Any update on when 2.0 will work on maverick?...

    Any update on when 2.0 will work on maverick? Thats all i'm waiting for.

    Bruce
  4. Replies
    1
    Views
    1,090

    360 columns project

    Has anyone tried this project? I have altered length only , no depth or width changes as per the instructions. I get pieces that do not round at 90 degrees to each other. Anyone? seems like the...
  5. Thread: copy offset

    by mobident
    Replies
    5
    Views
    1,940

    Aaargh .I have been messing with this for a month...

    Aaargh .I have been messing with this for a month now. I am only home on weekends, so that is adding to the frustration.
    I discovered there was a earlier version of designer on a mirror backup...
  6. Replies
    4
    Views
    1,707

    Ive sometimes had success converting to a line...

    Ive sometimes had success converting to a line and then converting back to spline to get 2 handles
  7. Replies
    6
    Views
    2,396

    Thanks AL, Stanv, KTJ, Just got home (work out...

    Thanks AL, Stanv, KTJ,
    Just got home (work out of town) had drilled out the bearing, got the e clip, got the y motor back together. All moving smooth, so got the project I was in the middle of up...
  8. Replies
    6
    Views
    2,396

    Y no, I can't bear it.

    I noticed the Y truck was getting a little bit stiff to move. released tension on the plate and Y moves fine. Good catch I'm thinking => caught a y axis bearing failure early before it could get bad....
  9. Replies
    12
    Views
    4,384

    Very Nice!

    Very Nice!
  10. Replies
    15
    Views
    6,336

    That is really spectacular!

    That is really spectacular!
  11. Thread: copy offset

    by mobident
    Replies
    5
    Views
    1,940

    I removed 1.184 prior to installing. I am on an...

    I removed 1.184 prior to installing. I am on an imac running mountain lion. I also have to update my license each time I start or I don't have 3D tools or collections I previously purchased
    Bruce.
  12. Thread: copy offset

    by mobident
    Replies
    5
    Views
    1,940

    copy offset

    Has copy offset been removed again with 1.185?

    I just used it a couple weeks ago and now I don't see it and help doesn't list it.
    Bruce
  13. Replies
    6
    Views
    2,047

    check board sensor

    Had an z axis stall into the wood 3 hours into carve. Now can't get project to start w check board sensor error. testing sensor and is reading the board fine. reads no board correctly. no drop off...
  14. Replies
    115
    Views
    65,737

    Typical experience for me in blender. messed...

    Typical experience for me in blender. messed around for a couple of hours, still cant figure out how to get the bas relief node installed...
  15. Replies
    5
    Views
    2,455

    Scott, Which part of the problem did you...

    Scott,
    Which part of the problem did you experience? Did you get an error message?
    Bruce
  16. Replies
    5
    Views
    2,455

    Thanks, Al I don't have the time on the cut...

    Thanks, Al

    I don't have the time on the cut motor, but as mentioned, the plastic cover had a good size hole in it and the gears were absolutely stuffed w saw dust.

    I had removed the belt and...
  17. Replies
    5
    Views
    2,455

    Y motor / belt slip error

    Y truck travel had become v. stiff and was getting "belt slip error"
    1) after bit plate touch, and travel to keypad side, error comes up and allows to continue.
    2)continue gives y axis fault.

    ...
  18. Replies
    7
    Views
    2,197

    Mine was failing to initiate the cut motor right...

    Mine was failing to initiate the cut motor right after asking for the first bit. Error code 93, I think. Upgraded to current software on the card and problem went away. Well, I have other problems,...
  19. Thread: STL importer

    by mobident
    Replies
    10
    Views
    4,081

    There is definitely something odd going on - I...

    There is definitely something odd going on - I can't open the stl files by the programs that converted them (blender Hex bryce). As pointed out above, they are being considered as text files (imac)....
  20. Thread: STL importer

    by mobident
    Replies
    10
    Views
    4,081

    Hmm, I also have not been able to use files...

    Hmm, I also have not been able to use files converted in blender, Hexagon and Bryce. I have converted wavefront objects to stl in each and they are unrecognized.

    How are you processing in blender?
  21. Replies
    1
    Views
    1,197

    Blue or Red loctite?

    What is the current recommendation for threads on the QC - blue or red loctite??
    Bruce
  22. Replies
    3
    Views
    6,097

    Final results

    Here are the final results. I'm no photographer, so I am having trouble finding the right shot to overcome the metallic paint reflections.

    The Wii car was cut out of a single cubcar kit. It didn't...
  23. Replies
    3
    Views
    6,097

    Pinewood derby car

    Here are two completely different designs to the age old cub car.

    I saw the Wii controller car that someone had posted a while back. One of my boys got very excited about it and so we did one.
    ...
  24. Replies
    24
    Views
    6,830

    blender

    I'm also interested in spending sometime with blender. haven't gone as far as even figuring out output types, but carrara may be a good 2nd stop. Anyone well versed in blender?
  25. Replies
    6
    Views
    2,189

    call CW. They can help you determine if its a...

    call CW. They can help you determine if its a dead card or a simple fix.
Results 1 to 25 of 60
Page 1 of 3 1 2 3