Search:

Type: Posts; User: Shacky; Keyword(s):

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. How sad. I haven't been on these forums for...

    How sad. I haven't been on these forums for quite a while, but I know how quickly he was always willing to help. He even had me call him once so he could walk me through how to fix something. God...
  2. Replies
    10
    Views
    878

    Thanks. Going to give it a good deep clean and...

    Thanks. Going to give it a good deep clean and lube and try again.
  3. Replies
    10
    Views
    878

    Maddeningly, I can't find the scale in my...

    Maddeningly, I can't find the scale in my workshop I bought just for this purpose. I'll figure something out and post the results tomorrow.
  4. Replies
    10
    Views
    878

    I will do that and report back. I appreciate...

    I will do that and report back. I appreciate your input!
  5. Replies
    10
    Views
    878

    I haven't checked the head pressure in a long...

    I haven't checked the head pressure in a long time. It's never been an issue and I just turn the crank until It clicks 3 times.
    I could check it. Yes, it seems to be touching the slap plate and...
  6. Replies
    10
    Views
    878

    Text depth problem

    I have made small signs in 3/4 inch oak with peoples names on it for years. (One name per sign.) I am doing my annual batch and am on the last one. For some reason, the name is not carving nearly as...
  7. Thread: New problem

    by Shacky
    Replies
    11
    Views
    1,070

    I think it started carving deeper, but kind of...

    I think it started carving deeper, but kind of irregularly. The board is perfect. Not warped, quite square, so it shouldn't be that.

    You can see on this picture, that it did it on the S below...
  8. Thread: New problem

    by Shacky
    Replies
    11
    Views
    1,070

    No, it did the rest of the sign fine, except for...

    No, it did the rest of the sign fine, except for one letter in a different part of the sign. The part in the photo, is the first to carve. I just checked the bit and everything is tight. I purposely...
  9. Thread: New problem

    by Shacky
    Replies
    11
    Views
    1,070

    83784I wonder why the E and the R came out wonky.

    83784I wonder why the E and the R came out wonky.
  10. Thread: New problem

    by Shacky
    Replies
    11
    Views
    1,070

    Thanks for the help. I'm carving now.

    Thanks for the help. I'm carving now.
  11. Thread: New problem

    by Shacky
    Replies
    11
    Views
    1,070

    Aha! By god I forgot about that!

    Aha! By god I forgot about that!
  12. Thread: New problem

    by Shacky
    Replies
    11
    Views
    1,070

    Great! Thanks for being willing to look at it! ...

    Great! Thanks for being willing to look at it! Here it is.
  13. Thread: New problem

    by Shacky
    Replies
    11
    Views
    1,070

    New problem

    I am setting up a long board for a sign. It is 59.75" long by 7.75' wide. I have added 7 inches and my design keeps all the words on the board. When I do the startup in my machine, everything...
  14. Replies
    96
    Views
    6,964

    Thanks. Maybe a little sharpie note on the side...

    Thanks. Maybe a little sharpie note on the side of something.
  15. Replies
    16
    Views
    1,797

    Not quite done, but close. Thanks again for the...

    Not quite done, but close. Thanks again for the help!
  16. Replies
    96
    Views
    6,964

    I guess that firmware update for the cut motor...

    I guess that firmware update for the cut motor did the trick. I just did a pretty big project and had no problems at all. Thanks for all the help!

    Just wondering. I put in a new cut motor with...
  17. Replies
    16
    Views
    1,797

    Just wanted to confirm that the part that is not...

    Just wanted to confirm that the part that is not on the board is just ignored. I was able to cut out the top with the bottom half off the board and then do the same with the bottom to make a two...
  18. Replies
    16
    Views
    1,797

    Great! Thanks! If I just place it on a board...

    Great! Thanks! If I just place it on a board and stretch it out to size am I correct that the machine will just ignore the part that isn't on the board? See what I mean by the attached pic.

    ...
  19. Replies
    96
    Views
    6,964

    I upgraded to 1.188 and applied the cut motor...

    I upgraded to 1.188 and applied the cut motor firmware update. I did a small job and it did not give me a check cut motor message at the beginning. Maybe that fixed it! :)
  20. Replies
    16
    Views
    1,797

    I've been trying to figure this out on my own,...

    I've been trying to figure this out on my own, but I'm not getting it. How do I make a pattern from the mpc attached?
  21. Replies
    16
    Views
    1,797

    I keep getting a message that this was made with...

    I keep getting a message that this was made with a newer version of the software and it won't open. I updated to 1.188 and it still won't work. Sorry to be so needy lately. I sure appreciate the...
  22. Replies
    96
    Views
    6,964

    Interesting. Hopefully this addresses the issue....

    Interesting. Hopefully this addresses the issue. I'll be doing this today. http://www.carvewright.com/firmware-update/
  23. Replies
    16
    Views
    1,797

    Big fancy sign top and bottom

    I'm looking for a top and bottom for a big sign I'm going to make. I would like it to have a cut out like the top and bottom of the pattern attached, but I would like it rotated so that I could cut...
  24. Replies
    96
    Views
    6,964

    I did flash the card as part of the...

    I did flash the card as part of the troubleshooting. What is the Check Cut Motor fix?
  25. Replies
    96
    Views
    6,964

    It's a brand new cut motor. Put it in as a part...

    It's a brand new cut motor. Put it in as a part of troubleshooting my original problem.
Results 1 to 25 of 381
Page 1 of 16 1 2 3 4