Search:

Type: Posts; User: 2A Finishing; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds; generated 16 minute(s) ago.

  1. Replies
    14
    Views
    5,189

    Head pressure was right close to 80lbs if I...

    Head pressure was right close to 80lbs if I remember correctly (I will check it again when I have a few minutes). The firmware version is 3.102 - I haven't had the machine a year, and it has under...
  2. Replies
    14
    Views
    5,189

    Honestly, I'm not comfortable disassembling this...

    Honestly, I'm not comfortable disassembling this machine to diagnose and repair it myself - Perhaps I should have spent more on a unit that didn't require me to perform diagnosis and repair on it...
  3. Replies
    14
    Views
    5,189

    I blow out the compression rollers before and...

    I blow out the compression rollers before and after each carve I do - It doesn't seem to have much effect if any. :(
  4. Replies
    14
    Views
    5,189

    Email sent to LHR, looking forward to a response...

    Email sent to LHR, looking forward to a response and instructions for shipping the machine in for diagnosis and repair. 97 hours on the usage odometer.
  5. Replies
    14
    Views
    5,189

    Well, I will get on the checks and maintenance...

    Well, I will get on the checks and maintenance and hopefully I can figure it out between the information available here and a phone call to CW as soon as possible (probably not before next week...
  6. Replies
    14
    Views
    5,189

    Trajectory Assertion Error: E24-0505

    Ok, I was attempting to carve a project (.063 depth, 11"x8" carve area, .75" thick board) - I got a random "board may have been removed" error, but since the board had obviously not moved or shifted...
  7. Replies
    13
    Views
    3,834

    I've never had a problem with oil finished wood...

    I've never had a problem with oil finished wood of almost any type outdoors in Florida weather (8 months of the year we get rain right around 2-3pm til at least 5 or 6pm EVERY DAY). I use a custom...
  8. Replies
    4
    Views
    1,682

    I use tongue and groove scraps for projects. I...

    I use tongue and groove scraps for projects. I use the machine to rip cut the tongue and groove off before starting.
  9. Replies
    19
    Views
    7,181

    How does this part work, you just install it into...

    How does this part work, you just install it into the carvetight chuck, or does that need to be removed?
  10. Replies
    19
    Views
    7,181

    There are .25" shank bits from the same company,...

    There are .25" shank bits from the same company, I just shared the wrong one is all. They sell both metric and standard.
  11. Replies
    19
    Views
    7,181

    I haven't tried them yet, but I've been looking...

    I haven't tried them yet, but I've been looking at these

    http://www.amazon.com/dp/B00SXCKHT6?psc=1
  12. Replies
    38
    Views
    6,090

    That would explain it. I forgot the tape.

    That would explain it. I forgot the tape.
  13. Replies
    38
    Views
    6,090

    Yes, I cut the ends off after running the...

    Yes, I cut the ends off after running the project. The biggest hole is an inch, but only .125 deep. If I drill deeper I do it with a max pass depth of .125 or .25
    I agree that the 3/16 bit would...
  14. Replies
    38
    Views
    6,090

    ok, bits came in today (yesterday) - sharp, new,...

    ok, bits came in today (yesterday) - sharp, new, shiny, beautiful, expensive bits lol

    So I figured that the only way to know was to try, and so I ran the drilling portion of the carve I broke the...
  15. Replies
    38
    Views
    6,090

    I certainly wasn't discounting the idea or the...

    I certainly wasn't discounting the idea or the input, like I said - just explaining that there was no change in the cover between yesterday and today, and I drilled several holes yesterday (ran two...
  16. Replies
    38
    Views
    6,090

    The right switch clicks a tiny fraction of an...

    The right switch clicks a tiny fraction of an instant before the left switch consistently same as it always has.
  17. Replies
    38
    Views
    6,090

    I hope you didn't take my response as being rude,...

    I hope you didn't take my response as being rude, because it wasn't intended this way. I'm afraid my frustration with the machine may be showing through a bit as it's spent more time down than...
  18. Replies
    38
    Views
    6,090

    Thanks. I'll add a piece of tape to the other...

    Thanks. I'll add a piece of tape to the other side as well.
  19. Replies
    38
    Views
    6,090

    The cover rests on the dust collector. If...

    The cover rests on the dust collector. If vibration was the issue in this particular case, I'd have been having cut motor problems from day 1 - this is the first time I've ever experienced this...
  20. Replies
    38
    Views
    6,090

    It's just cut to clear the Ringneck Blues dust...

    It's just cut to clear the Ringneck Blues dust collector (and I *ONLY* cut it because the RNB DC documentation stated that modifying the clear cover to clear the dust collector does NOT void my...
  21. Replies
    38
    Views
    6,090

    Like this? 78250

    Like this?

    78250
  22. Replies
    38
    Views
    6,090

    Thanks. I'll do that and see if it fails again....

    Thanks. I'll do that and see if it fails again. How long should I leave it to run before hitting the button to stop the test each time?
  23. Replies
    38
    Views
    6,090

    I made a new account on the store with the same...

    I made a new account on the store with the same email address and just placed my order for 2 1/8" cutting bits. :( Hope I can figure this out by the time they get here.
  24. Replies
    38
    Views
    6,090

    It won't accept the email that I ***KNOW*** I...

    It won't accept the email that I ***KNOW*** I used to register (I even have emails from LHR/carvewright in the inbox)
  25. Replies
    38
    Views
    6,090

    Lovely. I think my head is going to explode...

    Lovely. I think my head is going to explode today.

    Now I can't log in to the store site to buy new bits (going to buy two on the credit card in case this happens again)... It tells me my user...
Results 1 to 25 of 129
Page 1 of 6 1 2 3 4