Search:

Type: Posts; User: spalted; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Small Font Bit

    by spalted
    Replies
    1
    Views
    55

    I assume you're talking Centerline type text. I...

    I assume you're talking Centerline type text.
    I like the 60 degree V bit the best, but I think more important than the bit is the wood selection when you start getting real small.
    Tight grained...
  2. Replies
    3
    Views
    182

    Or maybe zoom in that area on your pattern or try...

    Or maybe zoom in that area on your pattern or try "Toggle Non-endpoint".
    You may have inadvertently left a stray node in your design.
  3. Thread: Query Select

    by spalted
    Replies
    2
    Views
    306

    Thank you Bergerud! All these years and I've...

    Thank you Bergerud!

    All these years and I've never figured out what that was for, but I never tried real hard either I just select from the carving list too, but it could come in handy.
  4. Replies
    2
    Views
    216

    "Toggle Non-endpoints" or Ctrl+E might help you...

    "Toggle Non-endpoints" or Ctrl+E might help you find the opening in the loop that Mugsowner mentioned.
  5. Replies
    11
    Views
    418

    LMAO.................. Those are great!

    LMAO.................. Those are great!
  6. Replies
    11
    Views
    418

    This is hilarious! I hope there is a video, or...

    This is hilarious!

    I hope there is a video, or at the very least a GIF that comes out of this........LOL
  7. Replies
    2
    Views
    135

    Should be everything you're looking for at the...

    Should be everything you're looking for at the bottom of this page.

    http://support.carvewright.com/getting-started/
  8. Replies
    2
    Views
    405

    I've had nothing but good experiences with the...

    I've had nothing but good experiences with the LHR team myself.

    I agree, I think they've earned a thank you.
  9. Replies
    19
    Views
    884

    Now that I think about it, wasn't there and old...

    Now that I think about it, wasn't there and old Tips and Tricks issue with a laminated wood project or something?

    Or was it forum posts that I've seen..................
    I dunno, either way it's a...
  10. Replies
    19
    Views
    884

    Welcome aboard! Nice job on your first project....

    Welcome aboard!
    Nice job on your first project.

    I've routed a lot of glued up wood and plywood.
    Glue does decrease tool life some I suppose, but so does using them. The way I look at it, cutting...
  11. Thread: Return

    by spalted
    Replies
    4
    Views
    551

    Al is offering up some great and helpful...

    Al is offering up some great and helpful information.

    I'll add a little to it too .
    CNC equipment is different than a 1950s table saw, it requires a lot more from the owner, and it's easy to make...
  12. Replies
    306
    Views
    24,663

    Thanks. It'll be a slow process for me to Learn...

    Thanks.
    It'll be a slow process for me to Learn it, I don't have much time available. Just a few minutes here and there, but I'll get it little by little, maybe............
  13. Replies
    7
    Views
    757

    Nicely done!

    Nicely done!
  14. Replies
    306
    Views
    24,663

    Lol..... OK I'm old enough too. I broke down...

    Lol.....
    OK I'm old enough too.

    I broke down and downloaded Blender again last night.
    It's come a long way in 5-7 years or whatever it's been since the last time I messed with it.
    Not that I...
  15. Replies
    10
    Views
    649

    Depending on your finished product, you might be...

    Depending on your finished product, you might be able to do it in layers.
    Your top layer at.25 or.125 thick cut the letters out by outlining them, then glue/laminate the cutout layer onto the back...
  16. Replies
    10
    Views
    627

    Set up right you don't suck up much dust. In a...

    Set up right you don't suck up much dust.
    In a typical vac hold down system you either plug the unused ports or some have a little valve that pops up unless there is a piece of wood on them, which...
  17. Replies
    5
    Views
    383

    Sometimes with solvent based coatings you can get...

    Sometimes with solvent based coatings you can get micro blisters, they appear similar to orange peel, or can leave the surface like sandpaper or sometimes people mistakenly assume it's dust...
  18. Replies
    10
    Views
    627

    I plan to use press to connect, or press-loc...

    I plan to use press to connect, or press-loc style fittings if I build one.
    I use them at work for building vacuum fixtures and for vac circuits all the time and they work really well.
    Here is an...
  19. Replies
    10
    Views
    627

    The changeable soil board type insert setup was...

    The changeable soil board type insert setup was all I could think of too.
    Digitalwoodshop I like your idea for creating the vac chamber.
    I was thinking on machining a vac plate style grid that a...
  20. Thread: Text Question

    by spalted
    Replies
    12
    Views
    571

    I think you have to adjust your spacing between...

    I think you have to adjust your spacing between lines on the right side of the text tool pane 3rd box down, or make each line a seperate text entry.
    Double spacing doesn't work for some reason, even...
  21. Replies
    8
    Views
    391

    Simple fixes are always good news. Glad it's...

    Simple fixes are always good news.

    Glad it's back up and running, thanks for the update.
  22. Replies
    10
    Views
    627

    Anybody try a Vacuum hold down sled?

    I'm sure it's a long shot, but have any of you tried or are currently using a vacuum hold down sled?

    I have a Gast 3/4 hp 8 cfm vac pump that I've used for various other shop shenanigans and I...
  23. Replies
    8
    Views
    391

    I'd give Tech support a call on Monday, I don't...

    I'd give Tech support a call on Monday, I don't know how to interpret those test results, but................

    It seems like it could be possibly a few things, the brushes, the switch on the cover,...
  24. Replies
    8
    Views
    391

    Somebody who has run into this before will...

    Somebody who has run into this before will probably be along shortly, but I'll have to do for now.

    Wicked weather right now made me think, is it cold in your shop?

    If it's marginally cold, I'd...
  25. Replies
    7
    Views
    404

    Thank you very much! I'll mess around with...

    Thank you very much!

    I'll mess around with those settings tomorrow.
    I've never experimented with those at all.
    Now I'm curious to see how they'll affect performance on my system.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4